793651
16
Zoom out
Zoom in
Previous page
1/156
Next page
16 ENGLISH
Positive stopper
The positive stopper is useful for setting the designated



base until it stops. The position where the tool base

Tighten the lever with the tool base at this position.
Fig.12: 1. Positive stopper
-1°-bevel cutting
To perform -1°-bevel cutting, loosen the clamping
screws and press the levers toward the direction of the

tighten the clamping screws.
Fig.13: 1. Lever
Sighting
For straight cuts, align the 0° position on the front of the

45° position with it.
Fig.14: 1.2. Cutting line

Lighting the lamp
CAUTION: Do not look in the light or see the
source of light directly.
To turn on the lamp without running the tool, pull the
󰀨
To turn on the lamp with the tool running, press and hold
󰀨
The lamp goes out 10 seconds after releasing the switch trigger.
Fig.15: 1. Lamp
NOTE:󰀨
the lamp. Be careful not to scratch the lens of lamp, or

Electric brake
This tool is equipped with an electric blade brake. If the

blade after switch lever release, have tool serviced at a
Makita service center.
CAUTION: The blade brake system is not a
substitute for blade guard. NEVER USE TOOL
WITHOUT A FUNCTIONING BLADE GUARD.
SERIOUS PERSONAL INJURY CAN RESULT.
Electronic function


Soft start feature
Soft start because of suppressed starting shock.
Constant speed control
Electronic speed control for obtaining constant speed.

kept constant even under load condition.
ASSEMBLY
CAUTION: Always be sure that the tool is
󰀨
before carrying out any work on the tool.
Hex wrench storage
When not in use, store the hex wrench as shown in the

Fig.16: 1. Hex wrench
Installing sub base
Install the sub base and tighten the clamping screws


using the guide rail.
Fig.17: 1. Clamping screw 2. Sub base
Installing or removing circular saw
blade
CAUTION: Be sure the circular saw blade is
installed with teeth pointing up at the front of the
tool.
CAUTION: Use only the Makita wrench to
install or remove the circular saw blade.
1. Loosen the lever on the depth guide and move the
base down.
Fig.18: 1. Lever
2. 

time, align the direction of the arrow on the blade with
the arrow on the tool.
For tool without the ring
Fig.19: 1. Hex bolt 2.3. Circular saw
blade 4.5. Arrow on the circular
saw blade 6. Arrow on the tool
For tool with the ring
Fig.20: 1. Hex bolt 2.3. Circular saw
blade 4. Ring 5.6. Arrow on the
circular saw blade 7. Arrow on the tool
3. 
blade cannot revolve and use the hex wrench to tighten
the hex bolt.
Fig.21: 1. Shaft lock 2. Hex wrench 3. Loosen
4. Tighten
To remove the circular saw blade, follow the installation
procedure in reverse.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita HS011G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita HS011G in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 22.49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info