Manual Makita HR 3210 (page 7 of 60) (English, German, Dutch, Danish, French, Italian)

78737

Zoom out

Zoom in

1/60

11. Do not leave the tool running. Operate the tool

only when hand-held.

12. Do not point the tool at any one in the area when

operating. The bit could fly out and injure

someone seriously.

13. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

14. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation and

skin contact. Follow material supplier safety data.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 1)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop.

Lighting up the lamps

For Model HR3210FCT (Fig. 2)

CAUTION:

• Do not look in the light or see the source of light

directly.

To turn on the lamp, pull the trigger. Release the trigger to

turn it off.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp.

Be careful not to scratch the lens of lamp, or it may

lower the illumination.

Speed change (Fig. 3)

The revolutions and blows per minute can be adjusted just

by turning the adjusting dial. The dial is marked 1 (lowest

speed) to 5 (full speed).

Refer to the table below for the relationship between the

number settings on the adjusting dial and the revolutions/

blows per minute.

CAUTION:

• If the tool is operated continuously at low speeds for a

long time, the motor will get overloaded, resulting in

tool malfunction.

• The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

Changing the quick change chuck for

SDS-plus

For Model HR3210FCT

The quick change chuck for SDS-plus can be easily

exchanged for the quick change drill chuck.

Removing the quick change chuck for SDS-plus

(Fig. 4)

CAUTION:

• Before removing the quick change chuck for SDS-plus

always remove the bit.

Hold the change cover with the thumb and the middle

finger and pull it in the direction arrow 1. With the change

cover pulled in that direction, hold the chuck cover with

the index finger. While holding the chuck cover so, pull out

the quick change chuck for SDS-plus in the direction of

arrow 2 at a stroke.

Attaching the quick change drill chuck

(Fig. 5)

Grasp the change cover and place the quick change drill

chuck on the spindle of the tool.

Make sure that the quick change drill chuck is secured by

trying to pull it several times.

Selecting the action mode

Rotation with hammering (Fig. 6)

For drilling in concrete, masonry, etc., depress the lock

button and rotate the change lever so that the pointer

points to the symbol. Use a tungsten-carbide tipped

bit.

Rotation only (Fig. 7)

For drilling in wood, metal or plastic materials, depress the

lock button and rotate the change lever so that the pointer

points to the symbol. Use a twist drill bit or wood bit.

Hammering only (Fig. 8)

For chipping, scaling or demolition operations, depress

the lock button and rotate the change lever so that the

pointer points to the symbol. Use a bull point, cold chisel,

scaling chisel, etc.

Number on

adjusting dial

Revolutions per

minute

Blows per minute

5 630 3,300

4 590 3,100

3 480 2,500

2 370 1,900

1 315 1,650

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita HR 3210 in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 1,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita HR 3210 Manual

Product: