Manual Makita HR 3210 (page 9 of 60) (English, German, Dutch, Danish, French, Italian)

78737

Zoom out

Zoom in

1/60

bounce around, uncontrolled. Pressing very hard on the

tool will not increase the efficiency.

Drilling in wood or metal (Fig. 20 - 22)

For Model HR3200C, HR3210C

Use the optional drill chuck assembly. When installing it,

refer to “Installing or removing the bit” described on the

previous page.

Set the change lever so that the pointer points to the

symbol.

For Model HR3210FCT

Use the quick change drill chuck as standard equipment.

When installing it, refer to “changing the quick change

chuck for SDS-plus” described on the previous page.

Hold the ring and turn the sleeve counter clockwise to

open the chuck jaws. Place the bit in the chuck as far as it

will go. Hold the ring firmly and turn the sleeve clockwise

to tighten the chuck. To remove the bit, hold the ring and

turn the sleeve counter clockwise.

Set the change lever to the symbol.

You can drill up to 13 mm diameter in metal and up to

32 mm diameter in wood.

CAUTION:

• Never use “rotation with hammering” when the quick

change drill chuck is installed on the tool.

The quick change drill chuck may be damaged.

• Pressing excessively on the tool will not speed up the

drilling. In fact, this excessive pressure will only serve

to damage the tip of your bit, decrease the tool

performance and shorten the service life of the tool.

• There is a tremendous twisting force exerted on the

tool/bit at the time of hole breakthrough. Hold the tool

firmly and exert care when the bit begins to break

through the workpiece.

• Always secure small workpieces in a vise or similar

hold-down device.

Diamond core drilling

When performing diamond core drilling operations,

always set the change lever to the position to use

“rotation only” action.

CAUTION:

• If performing diamond core drilling operations using

“rotation with hammering” action, the diamond core bit

may be damaged.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

Lubrication

CAUTION:

• This servicing should be performed by Makita

Authorized or Factory Service Centers only.

This tool requires no hourly or daily lubrication because it

has a grease-packed lubrication system. Lubricate the

tool every time the carbon brushes are replaced.

Run the tool for several minutes to warm it up. Switch off

and unplug the tool. (Fig. 23)

Loosen the four screws and remove the handle. Note that

the top screws are different from other screws. (Fig. 24)

Disconnect the connector by pulling them. (Fig. 25)

Loosen the two screws on crank cap cover and remove

the crank cap cover. (Fig. 26)

Align the change lever with the symbol, loosen the five

screws and then remove the crank cap. (Fig. 27)

CAUTION:

• Always remove the crank cap only after aligning the

change lever with the symbol . Never remove it

forcibly without aligning the change lever with the

symbol. Failure to do so does not allow reassembling.

(Fig. 28)

Rest the tool on the table with the bit end pointing

upwards. This will allow the old grease to collect inside

the crank housing.

Wipe out the old grease inside and replace with a fresh

grease (30 g). Use only Makita genuine hammer grease

(optional accessory). Filling with more than the specified

amount of grease (approx. 30 g) can cause faulty

hammering action or tool failure. Fill only with the

specified amount of grease.

CAUTION:

• Be careful not to damage the connector or lead wires

especially when wiping out the old grease.

To reassemble the tool, follow the disassembling

procedure in reverse.

CAUTION:

• Do not tighten the crank cap excessively. It is made of

resin and is subject to breakage. (Fig. 29)

Connect the connector firmly and then reinstall the

handle.

CAUTION:

• Be careful not to damage the connector or lead wires

especially when installing the handle.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• SDS-Plus Carbide-tipped bits

• Bull point

• Core bit

• Cold chisel

• Diamond core bit

• Hammer grease

• Scaling chisel

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita HR 3210 in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 1,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita HR 3210 Manual

Product: