Manual Makita hr 2400 (page 5 of 32) (German, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

388817

Zoom out

Zoom in

1/32

Operating instruction (Fig. 5)

Important:

Before plugging in the machine, always check to see

that the switch trigger actuates properly and returns to

the ‘‘OFF’’ position when released.

Switching ON and OFF (Fig. 5)

To switch on, press the trigger.

To switch off, release the trigger.

Continuous running (Fig. 5)

Press the trigger and at the same time slide the lock

lever upward. To stop from this lock position, press

the trigger and release it.

Variable trigger speed control (Fig. 5)

The speed varies from 0 to maximum, depending on

the pressure applied to the trigger. The more the

trigger is pressed, the faster the machine runs.

Reversing switch (Fig. 5)

Important:

Only reverse the direction of rotation when the motor

stops completely.

To change the direction of rotation:

Position FWD: right hand rotation

Position REV: left hand rotation

Three selecting action modes (Fig. 6)

For hammer drilling:

Turn the knob so that the arrow points toward the

symbol.

For drilling only:

Turn the knob so that the arrow points toward the

symbol.

For hammering only:

Turn the knob so that the arrow points toward the

symbol.

NOTE:

When it is hard to turn the knob, pull the switch trigger

half-way for running at low speed and turn the knob.

Torque limiter

The torque limiter will actuate when a certain torque

level is reached. The motor will disengage from the

output shaft. When this happens, the bit will stop

turning.

CAUTION:

As soon as the torque limiter actuates, switch off the

machine immediately. This will help prevent prema-

ture wear of the machine. Hole saws, core bit, dia-

mond core bit, etc. cannot be used with this machine.

They tend to pinch or catch easily in the hole. This will

cause the torque limiter to actuate too frequently.

Using cold chisel or bull point (Fig. 7)

1. Disconnect plug.

2. Remove the side grip from the machine.

3. Turn the knob to hammer drilling symbol

4. Install the cold chisel or bull point and then the

chisel adapter (optional accessory) on the

machine.

5. Rotate the cold chisel toward the direction suitable

for your work. Then secure the cold chisel and

chisel adapter by using the clamp screw on the

chisel adapter.

6. Turn the knob to hammering only symbol

Now you can use the cold chisel or bull point.

NOTE:

Always set ‘‘hammering only’’ action when using the

cold chisel or bull point. If you use ‘‘hammer drilling’’

or ‘‘drilling only’’ action, the hammering mechanism

may be damaged on the machine.

Drilling in wood or metal (Fig. 8)

Use the optional drill chuck assembly (consisting of

drill chuck and chuck adapter assembly). When

installing it, refer to ‘‘installing or removing drill bit’’

described on the previous page. Set the knob to

‘‘drilling only’’. You can drill up to 13 mm diameter in

metal and up to 38 mm diameter in wood. (Note:

When using a flat boring bit.)

NOTE:

Never set ‘‘hammer drilling’’ action when using the

drill chuck assembly because it may be damaged and

come off when reversing the machine.

MAINTENANCE

CAUTION:

Always be sure that the machine is switched off and

unplugged before carrying out any work on the

machine.

To maintain product safety and reliability, repairs,

maintenance or adjustment should be carried out by

Makita Authorized Service Center.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita hr 2400 in the language / languages: German, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita hr 2400

Makita hr 2400 User Manual - English, Dutch - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita hr 2400 Manual

Product: