Manual Makita hr 2400 (page 4 of 32) (German, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

388817

Zoom out

Zoom in

1/32

ENGLISH

Explanation of general view

1 Bit grease

2 Bit shank

3 Bit

4 Chuck cover

5 Wing bolt

6 Depth gauge

7 Side grip

8 Switch trigger

9 Lock lever

0 Reversing switch

q Action mode changing knob

w Chisel adapter

e Chisel

r Clamp screw

t Drill chuck

y Chuck adapter

SPECIFICATIONS

Model HR2400

Capacities

Concrete ...................................................... 24 mm

Wood .......................................................

38 mm

Steel ............................................................ 13 mm

No load speed (RPM) ................................ 0 – 1,200

Blows per minute ....................................... 0 – 4,200

Overall length ............................................... 333 mm

Net weight ....................................................... 2.3 kg

When using a flat boring bit.

•

Due to the continuing program of research and

development, the specifications herein are subject

to change without prior notice.

•

Note: Specifications may differ from country to

country.

Power supply

The machine should be connected only to a power

supply of the same voltage as indicated on the

nameplate, and can only be operated on single-phase

AC supply. They are double-insulated in accordance

with European Standard and can, therefore, also be

used from sockets without earth wire.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask, ear pro-

tectors and thickly padded gloves.

2. Be sure the bit is secured in place before

operation.

3. Under normal operation, the machine is

designed to produce vibration. The screws

can come loose easily, causing a breakdown

or accident. Check tightness of screws care-

fully before operation.

4. In cold weather or when the machine has not

been used for a long time, let the machine

warm up for several minutes by operating it

under no load. This will loosen up the lubrica-

tion. Without proper warm-up, hammering

operation is difficult.

5. Always be sure you have a firm footing. Be

sure no one is below when using the machine

in high locations.

6. Hold the machine firmly with both hands.

7. Keep hands away from moving parts.

8. Do not leave the machine running. Operate the

machine only when hand-held.

9. Do not point the machine at any one in the

area when operating. The bit could fly out and

injure someone seriously.

10. When drilling or chipping into walls, floors or

wherever ‘‘live’’ electrical wires may be

encountered, DO NOT TOUCH ANY METAL

PARTS OF THE MACHINE!

Hold the machine by the insulated grasping

surfaces to prevent electric shock if you drill

or chip into a ‘‘live’’ wire.

11. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing drill bit (Fig. 1,2&3)

Important:

Always be sure that the machine is switched off and

unplugged before installing or removing the bit.

Clean the bit shank and apply bit grease before

installing the bit. (Fig. 1)

Insert the bit into the machine. Turn the bit and push

it in until it engages. (Fig. 2)

If the bit cannot be pushed in, remove the bit. Pull the

chuck cover down a couple of times. Then insert the

bit again. Turn the bit and push it in until it engages.

(Fig. 3)

After installing, always make sure that the bit is

securely held in place by trying to pull it out.

To remove the bit, pull the chuck cover down all the

way and pull the bit out. (Fig. 4)

Adjusting depth of drilling (Fig. 4)

Loosen the wing bolt and adjust the depth gauge to

the desired depth. After adjusting, tighten the wing

bolt.

NOTE:

The depth gauge cannot be used at the position

where the depth gauge strikes against the gear

housing.

Side grip (Auxiliary handle) (Fig. 4)

The side grip swings around to either side, allowing

easy handling of the machine in any position. Loosen

the wing bolt on the side grip and swing the side grip

to the desired position. Then tighten the wing bolt to

secure the side grip.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita hr 2400 in the language / languages: German, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita hr 2400

Makita hr 2400 User Manual - English, Dutch - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita hr 2400 Manual

Product: