793633
15
Zoom out
Zoom in
Previous page
1/124
Next page
15 ENGLISH
CAUTION: Never switch on the tool when it
is in contact with the workpiece, it may cause an
injury to operator.
CAUTION: Always wear safety goggles or a
face shield during operation.
CAUTION: 󰀨
the tool and wait until the wheel has come to a
complete stop before putting the tool down.
CAUTION:

hand on housing and the other on the side grip (handle).
Grinding and sanding operation
Fig.27
Turn the tool on and then apply the wheel or disc to the workpiece.
In general, keep the edge of the wheel or disc at an


work the grinder in forward direction or it may cut into

󰀨

󰀨
diamond wheel
Optional accessory
WARNING:
Do not "jam" the wheel or apply
excessive pressure. Do not attempt to make an exces-
sive depth of cut. Overstressing the wheel increases



WARNING:
Do not start the cutting operation in
the workpiece. Let the wheel reach full speed and care-
fully enter into the cut moving the tool forward over
the workpiece surface.

WARNING:
During cutting operations, never
change the angle of the wheel. Placing side pressure
󰀨

WARNING: A diamond wheel shall be oper-
ated perpendicular to the material being cut.
For model GA7080 and GA9080, you can rotate the
switch handle.
󰀨
wheel with GA7080 / GA9080
Fig.28
󰀨
wheel with GA7081 / GA7082 / GA9081 / GA9082
Fig.29
Usage example: operation with diamond wheel with
GA7080 / GA9080
Fig.30
Usage example: operation with diamond wheel with
GA7081 / GA7082 / GA9081 / GA9082
Fig.31
Operation with wire cup brush
Optional accessory
CAUTION: Check operation of brush by run-
ning tool with no load, insuring that no one is in
front of or in line with brush.
NOTICE: Avoid applying too much pressure
which causes over bending of wires when using
the wire cup brush. It may lead to premature

Usage example: operation with wire cup brush
Fig.32
Operation with wire wheel brush
Optional accessory
CAUTION: Check operation of wire wheel
brush by running tool with no load, insuring that
no one is in front of or in line with the wire wheel
brush.
NOTICE: Avoid applying too much pressure
which causes over bending of wires when
using wire wheel brush. It may lead to premature

Usage example: operation with wire wheel brush
Fig.33
MAINTENANCE
CAUTION: Always be sure that the tool is
󰀨
perform inspection or maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,



NOTE: Do not loosen the screw on the cover.

Fig.34: 1. Screw
Air vent cleaning

Regularly clean the tool's air vents or whenever the

Fig.35: 1. Exhaust vent 2. Inhalation vent
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita GA7082 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita GA7082 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 21.89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info