793633
13
Zoom out
Zoom in
Previous page
1/124
Next page
13 ENGLISH
For tool with locking screw type
wheel guard
Mount the wheel guard with the protrusions on the wheel guard

the wheel guard to such an angle that it can protect the operator
according to work. Be sure to tighten the screw securely.
To remove wheel guard, follow the installation proce-
dure in reverse.
Fig.7: 1. Wheel guard 2.3. Screw
For tool with clamp lever type wheel guard
Optional accessory
WARNING: 
on the tool so that the closed side of the guard
always points toward the operator.
Loosen the nut, and then pull the lever in the direction of the arrow.
Fig.8: 1. Nut 2. Lever
Mount the wheel guard with the protrusions on the
-

that it can protect the operator according to work.
Fig.9: 1. Wheel guard 2.
Fig.10: 1. Wheel guard
Securely tighten the nut using a spanner, and then close the
lever in direction of the arrow to fasten the wheel guard. If
the lever is too tight or too loose to fasten the wheel guard,
open the lever and then loosen or tighten the nut using the

Fig.11: 1. Nut 2. Lever
To remove wheel guard, follow the installation proce-
dure in reverse.
Installing or removing depressed

Optional accessory
WARNING: When using a depressed center

on the tool so that the closed side of the guard
always points toward the operator.
CAUTION: Make sure that the mounting part








with its protrusion facing downward (facing towards the wheel).
Fig.12: 1. Lock nut 2. Depressed center wheel
3.4. Mounting part

that the spindle cannot revolve, then use the lock nut
wrench and securely tighten clockwise.
Fig.13: 1. Lock nut wrench 2. Shaft lock
To remove the wheel, follow the installation procedure
in reverse.

Optional accessory
WARNING: Always use supplied guard when
 Wheel can shatter during
use and guard helps to reduce chances of personal

Fig.14: 1. Lock nut 2. Flex wheel 3. Back up pad
4.


accessories page in this manual.
Super Flange
Optional accessory
Super Flange is a special accessory for model which is

Models with the letter F are standard-equipped with
󰀨
nut, compared with conventional type.
Installing or removing Ezynut
Optional accessory

CAUTION: Do not use Ezynut with Super

thread cannot be retained by the spindle.

spindle so that Makita Logo on Ezynut faces outside.
Fig.15: 1. Ezynut 2.3.
4. Spindle


Fig.16: 1. Shaft lock
To loosen the Ezynut, turn the outside ring of Ezynut
counterclockwise.
NOTE:
as the arrow points the notch. Otherwise a lock nut
wrench is required to loosen it. Insert one pin of the
wrench into a hole and turn Ezynut counterclockwise.
Fig.17: 1. Arrow 2. Notch
Fig.18
Installing or removing abrasive disc
Optional accessory
Fig.19: 1. Sanding lock nut 2.
3.
1. 
2. -
ing lock nut onto the spindle.
3.

the sanding lock nut clockwise with the lock nut wrench.
To remove the disc, follow the installation procedure in reverse.
NOTE:-

13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita GA7082 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita GA7082 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 21.89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info