599906

Makita EW220R Manual

31
Zoom out
Zoom in
Previous page
1/152
Next page
EN
8. EASY TROUBLESHOOTING
4. WHEN ENGINE DOES NOT START :
Perform the following checks before you take the pump to
your Makita dealer. If you still have trouble after completing
the checks, take the pump to your nearest Makita dealer.
(1) Is there a strong spark across the electrode ?
Is the stop switch at position “ I ” (ON)?
Remove and inspect the spark plug.
If the electrode is fouled, clean or replace it with new
one.
Remove the spark plug and connect it to the plug cap.
Pull the starter handle while grounding spark plug against
engine body. Try with a new spark plug if the spark is
weak or there is no spark.
The ignition system is faulty if there is no spark with a
new spark plug.
Wipe out spilled fuel carefully before testing.
Place spark plug as far away from spark plug
hole as possible.
Do not hold spark plug by hand while pulling
recoil starter.
WARNING
NOTE
The engine with oil sensor will stop automatically when
the oil level falls below the prescribed limit.
Unless the oil level is raised above the prescribed limit,
the engine will stop immediately after starting.
(3) Is the spark plug wet with gasoline?
Is the fuel cock opened? (Except EW120R)
Choke (close choke lever) and pull the starter handle five
or six times. Remove the plug and check if its electrode
is wet. If the electrode is wet, fuel is well supplied to your
engine.
When the electrode is dry, check where the fuel stops.
(Check the fuel intake of the carburetor and fuel filter
intake.)
(EW120R)
(Check the fuel intake of the carburetor.) (Except EW120R)
In case the engine does not start with well supplied fuel,
try using fresh fuel.
Pull the starter handle slowly and check if resistance is
felt. If little force is required to pull the starter handle,
check if the spark plug is tightened firmly. If the spark
plug is loose, tighten it.
(2) Is there enough compression?
1. FUNCTION OF OIL SENSOR
The engine will stop automatically when the oil level falls
below the safety limit. The engine cannot be started unless
the level is raised above the prescribed limit.
(See Fig.8
-
t)
2. RESTARTING
(1) Fill the crankcase with oil up to the proper level.
(2) As for restarting and operating the engine, refer to
section “4. OPERATING YOUR PUMP” on page 7.
Check the wire connector from the engine. It must be
connected securely to the wire from oil sensor.
When selecting the engine oil, refer to page 6 for the
recommended oil.
7. OIL SENSOR INSTRUCTIONS
(OPTIONAL)
1. PUMP DOES NOT RUN .
Engine dose not start.
(See 8.-4 “4. WHEN ENGINE DOES NOT START
”)
Sticking of impeller (Disassemble and clean.)
2. PUMPING VOLUME IS SMALL.
Sucking air at suction side.
(Check piping at suction side.)
Drop off engine output
(Consult your nearest dealer.)
Breakage of mechanical seal.
(Consult your nearest dealer.)
High suction lift (Lower.)
Suction hose is too long or thin.
(Use a thick hose in minimum length.)
Leak of water from water passage. (Stop leaking.)
Clogging of foreign substance in impeller.
(Disassemble and clean.)
Wear of impeller.
Strainer is clogged. (Clean.)
Engine speed is too low. (Consult your nearest dealer.)
3. PUMP DOES NOT SELFPRIME.
Suction of air at suction side.
(Check piping at suction side.)
Insufficient priming water inside pump casing
(Prime fully.)
Imperfect tightening of drain plug.
(Tighten the plugs completely.)
Engine speed is too low.
(Consult your nearest dealer.)
Sucking air from mechanical seal.
(Consult your nearest dealer.)
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EW220R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EW220R in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info