Manual Makita EW220R (page 30 of 152) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

599906

Zoom out

Zoom in

1/152

1. WATER (See Fig.

Drain all water from the drain plug.

6. PREPARATIONS FOR STORAGE

If you do not use the engine more than 1 month, discharge

fuel to prevent gum in the fuel system and carburetor parts.

EW120R

Pour out the fuel in the tank from its filler neck.

Push the primer pump of the carburetor until the fuel in

it is thoroughly discharged.

EW220R, EW220ST, EW320R, EW220TR,

EW320TR (See Fig.

Remove the strainer cup, place the strainer over a

container and open the strainer cock to discharge fuel

from the fuel tank.

Remove the drain screw of the carburetor float chamber

and discharge fuel.

When retightening drain plug, be sure to

clean the drain plug and the thread of casing.

Otherwise, the thread may be damaged.

CAUTION

2. DISCONNECT THE DELIVERY HOSE

Tilt the pump and drain all water from delivery hole. Severe

damage to pump may result if water freezes in the pumping

chamber.

WARNING Flame Prohibited

3. DISCHARGE FUEL (See Fig.

9. FUEL HOSE REPLACEMENT

(See Fig.

!5!5

!5,

!6!6

!6)

Replace the fuel hose every 1,000 hours or every 2 year.

If fuel leaks from fuel hose, replace the fuel hose immediately.

Take extreme caution when replacing fuel

hose ; gasoline is extremely flammable.

WARNING

10.

CHECKING BOLTS, NUTS AND SCREWS

Retighten loose bolts and nuts.

Check for fuel and oil leaks.

Replace damaged parts with new ones.

11. CLEANING PUMP INSIDE

Turn the knob counterclockwise and open the casing

cover holder.

Pull the casing toward you, and then remove the casing

and the inner casing.

Clean the inside of pump casing and casing cover with

clean water.

Remove the element, then clean it with a solution of warm

water and a mild detergent, thoroughly drying it afterward.

Install it in alignment with the lines as shown in illustration.

(See Fig.7

!2)

y Line (the slash mark)

u Element (the dotted line)

Wipe off any oil adhering to the area around the air

cleaner cover and breather with a cloth.

After cleaning, reassemble the cleaner cover (insert the

tab at the top first, then insert the bottom tab) and tighten

the fixing bolt.

EW220R, EW220ST, EW320R, EW220TR,

EW320TR (See Fig.

!3!3

!3,

!4!4

!4)

(1) Urethane Foam Element Type (See Fig.7 !3)

Remove the element and wash it in kerosene or diesel

fuel. Then saturate it in a mixture of 3 parts kerosene

or diesel fuel and 1 part engine oil. Squeeze the

element to remove the mixture and install it in the air

cleaner.

(2) Urethane Foam Dual Element Type (See Fig.7

!4)

Urethane Foam cleaning (See Fig.7 !4 w)

Wash and clean the urethane foam with detergent.

After cleaning, dry it. Clean the urethane foam

element every 50 hours.

Second element (See Fig.7 !4 q)

Clean by tapping gently to remove dirt and blow off

dust. Never use oil. Clean the paper element every 50

hours of operation, and replace element set every 200

hours.

NOTE

Clean and replace air cleaner elements more often when

operating in dusty environments. Replace the element in

case that dirt or dust can not be removed and/or that the

element is deformed or deteriorated.

4. ENGINE OIL (See Fig.

Change the engine oil with fresh oil.

Remove the spark plug, pour about 5 cc of engine oil

into the cylinder, slowly pull the starter handle of the

recoil starter 2 or 3 times, and reinstall the spark plug.

5. CLEAN AND STORE

Slowly pull the recoil starter handle until resistance is

felt and leave it in that position.

Clean the pump thoroughly with an oiled cloth, put the

cover on, and store the pump indoors in a well ventilated,

low humidity area.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita EW220R in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita EW220R Manual

Product: