599905

Makita EW120R Manual

27
Zoom out
Zoom in
Previous page
1/152
Next page
EN
1. STARTING (See Fig.
33
33
3)
(1) Open the fuel cock. (See Fig.3
-
q) (Except EW120R)
(2) Set the throttle lever to the idling position (L).
(See Fig.3-w) (EW120R)
Set the speed control lever 1/3 of the way towards the
high speed position. (See Fig.3-e) (Except EW120R)
(3) Set the stop switch to the position “
I
” (ON).
(See Fig.3
-
r,t)
(4) Close the choke lever. (See Fig.3
-
y,u)
If the engine is cold or the ambient temperature is low,
close the choke lever fully.
If the engine is warm or the ambient temperature is high,
open the choke lever half-way, or keep it fully open.
(5) Push the primer pump 7 to 10 times to feed the fuel to
the carburetor. (See Fig.3
-
i
-
q)
(6) Pull the starter handle slowly until resistance is felt. This
is the “compression” point. Return the handle to its
original position and pull swiftly. Do not pull out the rope
all the way. After starting the engine, allow the starter
handle to return to its original position while still holding
the handle. (See Fig.3
o,!0)
(7) After starting the engine, gradually open choke by turning
the choke lever and finally keep it fully opened. Do not
fully open the choke lever immediately when the engine
is cold or the ambient temperature is low, because the
engine may stop. (See Fig.3
!1,!2)
4. OPERATING YOUR PUMP
2. RUNNING (See Fig.
44
44
4)
(1) After the engine starts, set the speed control lever at the
low speed position (L) and warm it up without load for a
few minutes.
(See Fig.4
-
q,w)
(2) Gradually move the speed control lever toward the high
speed position (H) and set it at the required engine speed.
(See Fig.4
-
e,r)
Whenever high speed operation is not required, slow the
engine down (idle) by moving the speed control lever to
save fuel and extend engine life.
3. STOPPING (See Fig.
55
55
5)
(1) Speed control lever
Set the speed control lever at the low speed position and
allow the engine to run at low speed for 2 or 3 minutes
before stopping. (See Fig.5
-
q) (EW120R)
Set the speed control lever at the low speed position and
allow the engine to run at low speed for 1 or 2 minutes
before stopping. (See Fig.5
-
w) (Except EW120R)
(2) Set the stop switch to the position “
” (OFF).
(See Fig.5-e,r)
Do not stop the engine suddenly when it is running at
high speed.
(3) Close the fuel cock. (See Fig.5
-
t) (Except EW120R)
(4) Pull the starter handle slowly and return the handle to its
original position when resistance is felt. This operation is
necessary to prevent outside moist air from intruding
into the combustion chamber. (See Fig.5
y)
STOPPING ENGINE WITH THE FUEL COCK
(Except EW120R)
Close the fuel cock and wait for a while until the engine stops.
Avoid to let the fuel remain in the carburator over long periods,
or the passages of the carburator may become clogged with
impurities, and malfunctions may result.
5. MAINTENANCE
(See Fig.
66
66
6
)
1. DAILY INSPECTION
Before running the engine, check the following service items.
q Loose or broken bolts and nuts
w Clean air cleaner element
e Enough clean engine oil
r Leakage of gasoline and engine oil
t Enough gasoline
y Safe surroundings
u Check the priming water
i Excessive vibration, noise
NOTE
If the engine is operated at upside down, white smoke may
be exhausted from the muffler. (EW120R)
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EW120R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EW120R in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info