599870

Makita EG2850A Manual

20
Zoom out
Zoom in
Previous page
1/112
Next page
20
Handle Installation (Fig. 24)
1. Remove the two lugs in the pushrod inserted into the
rack, and line up the hole on the pushrod with the hole
on the rack. Next, insert the pushrod into the rack from
the outside and then screw in the M8 flange bolt on
the inside and tighten down the bolt.
TORQUE: 17 - 22 lbf•ft (24 - 29 N•m, 2.4 - 3.0 kgf•m)
Wheel Kit Installation (Fig. 25)
1. Line up the hole on the roller with the hole on the rack,
insert the roller shaft into the rack from the outside,
and then screw in the M8 flange bolt on the inside and
tighten down the bolt.
TORQUE: 17 - 22 lbf•ft (24 - 29 N•m, 2.4 - 3.0 kgf•m)
Fit the front stand (Fig. 26)
1. Insert an M8×100 bolt into the holes on the rubber
blanket, front stand, and rack mounting plate.
2. Screw the M8 flange bolt onto the M8×100 bolt from
the mounting plate and then tighten down the bolt.
Stopping the engine with remote control
1. Press the stop button.
2. Turn the engine switch on the generator to the
“O (OFF)” position.
3. Turn the fuel valve lever on the generator to the
“O (OFF)” position.
Battery Tray (Fig. 27)
NOTE:
Battery is not included. Use a battery (rating: 12V-10Ah,
L x W x H: maximum 160 mm x 90 mm x 160 mm)
available in the market.
1. Connect the black power line (ground electrode) on
the electric generator to the negative electrode on the
battery and the red power line to the positive electrode
on the battery.
2. Place the battery connected to the power lines into the
battery box on the rack.
3. Hang each of the two card buckles on the rubber belt
onto one of the two hangers on the battery box.
WARNING:
Lead and lead compounds are used in battery posts,
terminals, and related accessories. Always wash
hands after handling.
Engine Oil (Fig. 13)
The generator is shipped WITHOUT OIL in the engine.
Place the generator on a stable and level surface. Add
enough of the recommended oil to bring the oil level to the
top of the oil filler neck.
Use a 4-stroke motor oil that satisfies the requirements for
API service category SJ or later (or equivalent).
Do not overfill the engine with oil. If the engine is
overfilled, the excess oil may get transferred to the air
cleaner housing and air filter.
WARRANTY SERVICE
INFORMATION
CUSTOMER SERVICE INFORMATION
The personnel at the servicing dealership are trained
professionals. They should be able to answer most
questions you may have. If there is a problem that your
dealer does not solve to your satisfaction, please discuss
it with the Service Manager or General Manager of the
dealership. Almost all problems are solved in this way.
If you are dissatisfied with the decision made by the
dealership’s management, contact the Makita
Corporation.
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine: Petrol Generator
Model No./ Type: EG2250A, EG2850A, EG4550A,
EG5550A, EG6050A
Specifications: see "SPECIFICATIONS" table.
are of series production and
Conforms to the following European Directives:
2000/14/EC, 2004/108/EC, 2006/42/EC,
2006/95/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN12601, EN55012, EN61000, EN60204-1
The technical documentation is kept by:
Makita International Europe Ltd.
Technical Department,
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
The conformity assessment procedure required by
Directive 2000/14/EC was in Accordance with annex VI.
Notified Body:
AV TECHNOLOGY LTD
AVTECH House,Arkle Avenue
Stanley Green Trading Estate
Handforth,Cheshire
SK9 3RW,United Kingdom
Identification number 1067
Model EG2250A
Measured Sound Power Level: 94 dB (A)
Guaranteed Sound Power Level: 95 dB (A)
Model EG2850A, EG4550A, EG5550A, EG6050A
Measured Sound Power Level: 95 dB (A)
Guaranteed Sound Power Level: 96 dB (A)
27.12.2013
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EG2850A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EG2850A in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info