599867

Makita EBH341U Manual

16
Zoom out
Zoom in
Previous page
1/232
Next page
16
ADJUSTMENT OF LOW-SPEED ROTATION (IDLING)
When it is necessary to adjust the low-speed rotation (idling), perform it by the carburetor adjusting screw.
CHECKUP OF LOW-SPEED ROTATION
– Set the low-speed rotation to 3,000 min
-1
.
If it is necessary to change the rotation speed, regulate the adjusting screw
(illustrated on the left), with Phillips screwdriver.
– Turn the adjusting screw to the right, and the engine rotation will increase.
Turn the adjusting screw to the left, and the engine rotation will drop.
– The carburetor is generally adjusted before shipment. If it is necessary to
readjust it, please contact Authorized Service Agent.
Adjusting screw
Carburetor
CAUTION:
The cutting tools mentioned below must only be resharpened by an authorized
facility. Manual resharpening will result in imbalances of the cutting tool causing
vibrations and damage to the equipment.
– cutter blade
An expert resharpening and balancing service is provided by Authorized
Service Agents.
NOTE:
To increase the service life of the cutter blade it may be turned over once, until
both cutting edges have become blunt.
RESHARPENING THE CUTTING TOOL
Operation of Throttle Lever
With the throttle lever main unit held by hand (with the lock-off lever pushed), pull the throttle lever and the engine rotation will be increased.
Release the throttle lever, and the engine will run idle again.
Release the hand from the throttle lever main unit, and the lock-off lever will return automatically so that the throttle lever will not be pulled by
mistake.
Adjustment of Engine ROTATION
When adjusting the engine rotation with the throttle lever opened to the full, turn the throttle control dial. Turn the dial clockwise, and the engine
rotation will be reduced. Turn the dial counterclockwise, and the engine rotation will be increased.
NYLON CUTTING HEAD
The nylon cutting head is a dual Petrol Brushcutter head capable of both
automatic and bump & feed mechanisms.
The nylon cutting head will automatically feed out the proper length of nylon
cord by the changes in centrifugal force caused by increasing or decreasing
rpms. However, to cut soft grass more efficiently, bump the nylon cutting head
against the ground to feed out extra cord as indicated under operation section.
Operation
– Increase the nylon cutting head speed to approx. 6,000 min
-1
.
Low speed (under 4,800 min
-1
) is not suitable, the nylon cord will not feed out
properly at low speed.
– The most effective cutting area is shown by the shaded area.
If the nylon cord does not feed out automatically proceed as follows:
1. Release the throttle lever to run the engine idle and then squeeze the
throttle lever fully. Repeat this procedure until the nylon cord feeds out to
the proper length.
2. If the nylon cord is too short to feed out automatically with the above
procedure, bump the knob of the nylon cutting head against the ground to
feed out the nylon cord.
3. If the nylon cord does not feed out with procedure 2, rewind/replace the
nylon cord by following the procedures described under “Replacing the
nylon cord.”
Most effective cutting area
Idle speed
Full speed
Knob
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EBH341U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EBH341U in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 5,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info