448381
12
Zoom out
Zoom in
Previous page
1/149
Next page
12
MOUNTING OF HANDLE
Fix a barrier to the left side of the machine together with the
handle for operators protection.
Do not adjust position of the loop handle too close to the control
grip. Keep not less than 25cm distance between the handle
and the grip.
(a distance collar is provided for this purpose.)
MOUNTING OF PROTECTOR
To meet the applicable safety provisions, only the tool/protector
combinations as indicated in the table must be used. Failure to do
so may result in serious injury or death to user or bystanders.
Be sure to use genuine MAKITA cutter blade or nylon
cutting head.
The cutter blade must be well clean, sharp and free of cracks
or breakage.
If the cutter blade contacts any hard objects or stones during
operation, stop the engine and check the blade immediately.
Clean and sharpen or replace the cutter blade at least every
three hours of operation.
The outside diameter of the cutter blade must not exceed 255
mm (10-1/32). Never use any blades surpassing 255 mm (10-
1/32) in outside diameter.
CAUTION : The appropriate guard must always be in-
stalled, for your own safety and in order to
comply with accident-prevention regulations.
Operation of the equipment without the
protector being properly in place must never
be attempted.
Fix protector to a gear case by 4 bolts firmly
Never use a blush cutter without a protector or with a broken
protector.
MOUNTING OF CUTTER BLADE OR
NYLON CUTTING HEAD
Turn the machine upside down, and you can replace the cutter
blade or nylon cutting head easily.
Mounting of cutter blade
Fit a cutting blade and other parts in the order as in the illustra-
tion. Thrust a bar or allen wrench into a hole of the gear case
until the cutting blade is locked and will not turn. Tighten a nut
by turning to counter-clockwise with a combination wrench.
(Note that the nut is tightened or loosened in the opposit
direction of a usual nut.)
The nut must be re-tightened every time before use.
For this brush cutter, we recommend the cutting attachments on
the right.
Never attempt to cut a tree, a log, wood or other hard materials.
[Tightening torque: 28 48 N
m]
NOTE : Always wear gloves when handling the cutter
blade.
Mounting of nylon cutting head
The blade cap, bolt cover and nut are not necessary for
mounting the nylon cutting head. The nylon cutting head should
go on top of the grass cover.
Insert the allen wrench through the hole in the gear case and
rotate the blade holder until it is locked with the alln wrench.
Then screw the nylon cutting head onto the shaft by turning it
counter-clockwise.
Remove the allen wrench.
Star Blade
Protector for metal
blades
Eddy Blade
PART NO.
6418501400
PART NO.
6418501900
PART NO.
6118502000
Nut
Bolt cover
Blade cap
Blade
Grass cover
Blade holder
Protector plate
Protector
Gear case
PART NO.6348003000 PART NO.174345800
Nylon cutting head
to engine
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EBH341R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EBH341R in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info