599865

Makita EB7650TH Manual

17
Zoom out
Zoom in
Previous page
1/172
Next page
17
INSPECTION AND MAINTENANCE
CAUTION:
Before inspection and maintenance, stop the engine and allow it to cool down. Remove the spark plug and plug cap.
Otherwise the operator may suffer burn or serious injury due to an accidental start-up.
After inspection and maintenance, make sure that all parts are assembled. Then, proceed to operation.
1. Replacement of engine oil
Deteriorated engine oil will shorten the life of the sliding and rotating parts to a great extent. Be sure to check the period and quantity of
replacement.
CAUTION:
The engine main unit and engine oil still remain hot just after the engine is stopped. In replacement of oil, make sure that the engine main unit and
engine oil are sufficiently cooled down. Otherwise, there may remain a risk of scald. Allow sufficient time after stopping engine for the engine oil
to return to the oil tank to ensure accurate reading of the oil level indicator.
If the oil filled above the limit, it may become dirty or may catch fire with white smoke.
Interval of replacement: After first 20 operating hours, followed by every 50 operating hours
Recommended oil: SAE10W-30 oil, API Classification SF Class or higher (4-stroke engine oil for automobile)
●
–
●
●
●
Oil Change Procedure
Please follow these steps when changing the oil:
(1) Set the blower down on a level surface.
(2) Put a waste oil container under the drainage hole (1) to catch
the oil as it drains out. The container should have a capacity of
at least 220 ml to be able to catch all of the oil.
(3) Loosen the oil drain bolt (2) to let the oil drain out. Be careful not
to allow oil to get on the fuel tank or other parts.
CAUTION:
Be careful not to lose the gasket (aluminum washer) (3). Put
the oil drain bolt (2) in a location where it will not accumulate
dirt.
(4) Remove the oil cap (4). (Removing the oil cap (4) allows the oil
to drain easily.)
CAUTION:
Be sure to set the oil cap (4) down in a location where it will
not accumulate dirt.
(5) As the level of the oil being drained decreases, tilt the blower
over on to the side with the drain so that the oil will completely
drain out.
(6) After the oil has completely drained out, tighten the oil drain bolt
(2) securely. If the bolt is not tightly fastened, this may result in
an oil leak.
CAUTION:
Do not forget to put the gasket (aluminum washer) (3) back
on when reattaching the drain plug.
(7) Adding oil during the oil change procedure is performed in the
same manner as the separately explained procedure for adding
oil whenever the level is insufficient. Always add oil by filling
from the opening under the oil cap.
(Specified oil level: Approximately 220 ml)
(8) After filling with oil, tighten the oil cap (4) securely to prevent oil
leaks.
●
●
●
(2)
(3)
(4)
(1)
Points in replacement of engine oil
Never discard replaced engine oil in garbage, earth or sewage ditch. Disposal of oil is regulated by law. In disposal, always follow the relevant
laws and regulations. For any points remaining unknown, contact Authorized Service Agent.
Oil will deteriorate even when it is kept unused. Perform inspection and replacement at regular intervals (replace with new oil every 6 months).
●
●
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EB7650TH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EB7650TH in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 6,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info