793624
20
Zoom out
Zoom in
Previous page
1/132
Next page
20 ENGLISH
If you are repeating the wire tying processes in

from the switch trigger. Then, continue to operate
the switch trigger.
If you pull the switch trigger when there is no tie
wire left, an error is displayed. Replace with a new
tie wire and restart the tool.
Tying tips
Tilt the tool at a 45° angle against the crossed
rebars, and tie the wire in alternate orientations as

Fig.41
 
sections of crossed rebars.
Fig.42
 󰀩
orientation and perform tying twice so that tying
strength increases.
Fig.43
NOTICE: When you make the second tie, bend

tie. Otherwise, the wire may be repelled a second
time. It may cling to the tool tip, and the hook may be
damaged.
Replacing the tie wires
CAUTION: When you replace the wire, be sure
󰀨
the battery cartridge. Failure to do so may cause an
accident.
1. When wire has been used up, an error tone will
sound and error "1" will be displayed.
2. 󰀨
the battery cartridge.
3. Push the release lever, and lock it with the lock
lever.
Fig.44: 1. Release lever 2. Lock lever
4. Remove the wire reel from the tool.
NOTE: When wire has been used up normally,
approximately 20 cm of the wire remains wound on
the reel. In this state, replace the wire reel with a new
one.
󰀩
follow the steps below.
1. Insert the battery cartridge into the tool, and
turn the power on. The tool feeds the wire and cuts it
automatically.
2. 󰀨
the battery cartridge.
3. Remove the wire breaks using tools such as nip-
pers or pliers.
MAINTENANCE
CAUTION: Always be sure that the tool is
󰀨
before attempting to perform inspection or
maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,

be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Cleaning the cutter section
When the tool is used, dust and wire particles may
become adhered to the cutter section. In such a case,
clean the cutter section according to the following pro-
cedure. The cleaning should be done each time you use
up a box of reel. (50 pcs.)
Using the wire brush
1. Open the reel cover.
Fig.45: 1. Reel cover
2. Push the release lever, and lock it with the lock
lever.
Fig.46: 1. Release lever 2. Lock lever
3. Pass the wire brush through the guide.
When inserting the wire brush, hold it short and push it
into the guide little by little.
Fig.47: 1. Wire brush
Fig.48: 1. Gear 2. Guide 3. Wire brush
4. Push in the wire brush until its top end comes out
from the tip of the arm. And then pull out the wire brush.
This action is enough with one time.
Fig.49: 1. Arm 2. Wire brush
5. Close the reel cover.
Fig.50: 1. Reel cover
Using the air duster gun
Open the reel cover, push the release lever, and lock it
with the lock lever. Then bring the air duster gun close
to the guide and blow the air. Make sure the air comes
from the tip of the arm.
Fig.51: 1. Air duster gun 2. Guide
Cleaning with disassembly
If the cutter section is clogged or a wire is caught in it,
disassemble the parts and clean them.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DTR181 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DTR181 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 38.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info