793624
17
Zoom out
Zoom in
Previous page
1/132
Next page
17 ENGLISH
Main power switch
CAUTION:
When you turn the power on, never
bring your limbs or face close to the binding or rotat-
ing parts of the tool tip.
CAUTION: When the power is turned on,
never touch the binding or rotating parts of the
tool tip.
CAUTION:
Before inserting the battery cartridge,

and lock the trigger. If you insert the battery cartridge
while the switch trigger is being pulled, it may cause an
accident if the wire tying process is accidentally carried out.
Fig.3
When you press the power button, the power turns
on and the tying mode lamp lights up. In order for the

-
matically. When you press the power button again, the
󰀨
Fig.4: 1. Tying mode lamp 2. Power button
NOTE:
󰀨
switch trigger is not pulled for 10 minutes, the tool is auto-
󰀨
NOTE: To restart the tool, turn the power on again.
Mode switching button
When the power is turned on and the tying mode lamp
is lit, you can select the single actuation mode or the
continuous actuation mode via the mode switching but-
ton. When you turn the power on again, the tool starts in
the mode that was most recently selected.
Fig.5: 1. Mode switching button 2. Single actuation
mode 3. Continuous actuation mode
Switch action
WARNING: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
CAUTION: When not operating the tool,
depress the trigger-lock button from side to
lock the switch trigger in the OFF position.
Fig.6: 1. Switch trigger 2. Trigger-lock button
To prevent the switch trigger from accidentally pulled,
the trigger-lock button is provided. To start the tool,
depress the trigger-lock button from A side and pull the
switch trigger. Release the switch trigger to stop. After
use, press in the trigger-lock button from B side.
When you pull the switch trigger, the tool performs the next
sequential operations as follows, and the tool stops automatically.
1. Feed the wire.
2. Cut the wire.
3. The hook holds and twists the wire.
4. The hook returns to the original position.
Tying strength setting
CAUTION: Be sure to lock the trigger before
starting the adjustment. When you turn the power
on, never bring your limbs or face close to the
binding or rotating parts of the tool tip. Otherwise,

Fig.7


the display panel.
Fig.8: 1.2. Display
panel
󰀨
tying, check the twisted portion for breakage.
󰀨

again.

When the battery voltage drops below the required
level, the tool will stop operating, an error tone will
sound, and the number "4" will appear on the display
panel. The error tone will continue to sound until the
󰀨
NOTE: If the ambient temperature is extremely low,
the error tone may sound even when the battery
󰀩
ASSEMBLY
CAUTION: Always be sure that the tool is
󰀨
before carrying out any work on the tool.
Loading the tie wire (wire reel)
CAUTION: Before mounting or dismounting
tie wires and accessories, be sure to turn the
󰀨
cartridge. Failure to do so may cause an accident.
NOTICE: Using wires other than Makita's genu-
ine tie wires may cause the tool to malfunction.
1. Push the release lever, and lock it with the lock
lever.
Fig.9: 1. Release lever 2. Lock lever
When you push the release lever, a gap is created
between the left and right feed gears.
Fig.10: 1. Release lever 2. Lock lever 3. Feed gears
2. Open the reel cover.
Fig.11: 1. Reel cover
3. Mount the wire reel on the tool in the orientation

Fig.12: 1. Wire reel
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DTR181 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DTR181 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 38.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info