691391

Makita DPO600 Manual

8
Zoom out
Zoom in
Previous page
1/68
Next page
8 ENGLISH
Switch action
CAUTION: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
CAUTION: Switch can be locked in "ON" posi-
tion for ease of operator comfort during extended
use. Apply caution when locking tool in "ON"
position and maintain rm grasp on tool.
CAUTION: Do not install the battery cartridge
with the lock button engaged.
CAUTION: When not operating the tool,
depress the trigger-lock button from side to
lock the switch trigger in the OFF position.
►Fig.3: 1. Trigger-lock button
►Fig.4: 1. Switch trigger 2. Lock button 3. Trigger-
lock button
Topreventtheswitchtriggerfromaccidentallypulled,the
trigger-lock button is provided. To start the tool, depress
thetrigger-lockbuttonfromA( )sideandpulltheswitch
trigger.Toolspeedisincreasedbyincreasingpressureon
the switch trigger. Release the switch trigger to stop. After
use,depressthetrigger-lockbuttonfromB( )side.
For continuous operation, depress the lock button while
pulling the switch trigger, and then release the switch trigger.
Tostopthetool,pulltheswitchtriggerfully,thenreleaseit.
Speed adjusting dial
►Fig.5: 1.Speedadjustingdial
Therotatingspeedcanbechangedbyturningthe
speedadjustingdialtoagivennumbersettingfrom1to
5. Higher speed is obtained when the dial is turned in
the direction of number 5. And lower speed is obtained
when it is turned in the direction of number 1.
Refer to the table for the relationship between the number
settings on the dial and the approximate rotating speed.
Normal mode
Number Orbits per min. Pad rotating speed per
minute in random orbit with
forced rotation mode
1 1,600 180
2 2,500 290
3 4,000 460
4 5,600 650
5 6,800 780
Finishing mode
Number Orbits per min. Pad rotating speed per
minute in random orbit with
forced rotation mode
1 1,600 180
2 2,200 250
3 3,300 380
4 4,400 500
5 5,200 600
NOTICE: If the tool is operated continuously
at low speeds for a long time, the motor will get
overloaded, resulting in tool malfunction.
NOTICE: The speed adjusting dial can be turned
only as far as 5 and back to 1. Do not force it past
5 or 1, or the speed adjusting function may no
longer work.
Selecting the action mode
Turn the change knob to alter the rotation mode.
►Fig.6: 1. Change knob
NOTICE: Always turn the knob fully. If the knob
is in the middle position, you cannot turn on the
tool.
NOTICE: You cannot change the action mode
when the tool is switched on.
Random orbit with forced rotation
mode
►Fig.7: 1. Change knob
Random orbit with forced rotation mode is orbital action
with forced rotation of the pad for rough polishing such
as surface treatment.
Rotate the change knob counterclockwise for random
orbit with forced rotation mode.
Random orbit mode
►Fig.8: 1. Change knob
Random orbit mode is orbital action with free rotation of
thepadfornepolishing.
Rotate the change knob clockwise for random orbit
mode.
Finishing mode
Inthenishingmode,youcanoperatethetoolwithout
applyingexcessiveload.Thismodeissuitableforn-
ishing operation.
Tousethetoolinthenishingmode,pulltheswitch
trigger and release it to turn on the tool, and then press
the mode switching button. The lamp lights up in green.
To return to the normal mode, press the mode switching
button while the tool is turned on.
►Fig.9: 1. Lamp 2. Mode switching button
NOTE: You cannot change the mode when the tool
is running.
Accidental restart preventive
function
Ifyouinstallthebatterycartridgewhilepullingthe
switch trigger or locking the switch trigger, the tool does
not start. To start the tool, release the switch trigger, and
then pull the switch trigger.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DPO600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DPO600 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 14,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info