691826

Makita DPB182 Manual

8
Zoom out
Zoom in
Previous page
1/64
Next page
8 ENGLISH
Lighting up the front lamp
CAUTION: Do not look in the light or see the
source of light directly.
Pulltheswitchtriggertolightupthelamp.Thelamp
keepsonlightingwhiletheswitchtriggerisbeing
pulled.Thelampgoesoutjustaftertheswitchtriggeris
released.
►Fig.4: 1. Lamp
NOTE: Do not apply impact to the lamp, which may
cause damage or shorted service time to it.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing the band saw blade
CAUTION: Oil on the band saw blade can
cause the blade to slip or come off unexpectedly.
Wipe off all excess oil with a cloth before install-
ing the band saw blade.
CAUTION: Always wear protective gloves
when handling the band saw blade.
CAUTION: Use caution when handling the
band saw blade to avoid cut by the sharp edge of
the blade teeth.
CAUTION: Keep your body away from
the band saw blade when checking the blade
movement.
CAUTION: When turning the blade tightening
lever clockwise to release the tension on the band
saw blade, point the tool downward because the
band saw blade may come off unexpectedly.
►Fig.5: 1. Tighten 2. Loosen 3. Blade tightening lever
Toinstallthebandsawblade:
1. Turnthebladetighteningleverclockwiseuntilit
stops to loosen the wheel.
2. Matchthedirectionofthearrowsonthebandsaw
bladeandonthewheels.
3. Insertthenon-serratedsideofthebandsawblade
into the upper holder and lower holder. Make sure the
bandsawbladeinbothupperandlowerholdertouches
tothebottombearings.
►Fig.6: 1. Lower holder 2. Upper holder 3. Bottom
bearing
4. Withpressingthemiddlepartofthebandsaw
blade,positionthebladearoundonewheel.Movingthe
wheeltoAsidemakesiteasiertodoso.
►Fig.7: 1. Wheel 2.Rubbertire
5. Positionthebandsawbladeonanotherwheel
similarly.
6. Positiontheedgeofthebandsawbladeonrubber
tire.
7. Holdthebandsawbladeinplaceandturnthe
bladetighteninglevercounterclockwiseuntilitstops.
Thisplacespropertensiononthebandsawblade.
NOTICE: Make sure that the band saw blade is
correctly positioned around the wheels.
NOTICE: Start and stop the tool two or three
times to make sure that the band saw blade runs
properly on the wheels.
Toremovethebandsawblade,followtheinstallation
procedure in reverse.
Adjusting the stopper plate position
In the ordinary operation, protrude the stopper plate to
theAsidefully.
Whenthestopperplatestrikesagainsttheobstacles
likeawallorthelikeatthenishingofacut,loosentwo
boltsandslideittotheBsideinthegure.
Afterslidingthestopperplate,secureitbytightening
twoboltsrmly.
►Fig.8: 1. Stopper plate 2. Bolts 3.Bandsawblade
Installing hook
Optional accessory
CAUTION: Do not use the hook for other pur-
pose than temporarily hanging the tool. Doing so
may cause the hook come off from the tool and result
inpersonalinjury.
Hook is useful for hanging the tool. Hang the tool on a
pipeviceorothersuitable,stablestructure.
To install the hook, set the hook alongside the groove
and tighten it with two screws.
►Fig.9: 1. Hook 2. Screws
OPERATION
CAUTION: Always insert the battery cartridge
all the way until it locks in place. If you can see the
redindicatorontheuppersideofthebutton,itisnot
locked completely. Insert it fully until the red indicator
cannotbeseen.Ifnot,itmayaccidentallyfalloutof
thetool,causinginjurytoyouorsomeonearound
you.
CAUTION: Always hold front and rear handle.
Never hold the tool body or guards. Hands may
slipfromtheselocationsandcontactwiththeband
sawblade.Itmayresultinpersonalinjury.
CAUTION: Make sure to hold the tool rmly
when turning on or off the tool or when cutting.
Otherwisethetoolmayfallandcausepersonalinjury.
NOTE: When cutting metal, wearing gloves is recom-
mendedtoprotectyourhandsfromhotyingchips.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DPB182 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DPB182 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 13,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info