Manual Makita DMR107 (page 8 of 72) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Spanish)

657982

Zoom out

Zoom in

1/72

Note:

During operating volume control, you can press in

Tuning/Volume control knob to change volume control

to tuning control status.

5. To turn off the radio, press the Power button. Display

will show OFF.

Manual Tuning

1. Press the Power button to turn on the radio.

2. Select the required waveband by pressing the Band

button. Adjust the antenna as described above.

3. A single rotary to the Tuning/Volume control knob will

change the frequency in the following increment:

FM: 50 or 100 kHz

AM (MW): 9 or 10 kHz

Note:

If the radio is in volume control status, press in the

tuning/volume control to become Tuning status.

4. Keep on rotating the Tuning/Volume control knob until

the required frequency shown on the display.

5. Rotate the Tuning/Volume control knob to get required

sound level.

6. To turn off the radio, press the Power button. Display

will show OFF.

Storing stations in preset

memories

There are 5 memory presets for each waveband.

1. Press the Power button to turn on the radio.

2. Tune to required station using one of the methods

previously described.

3. Press and hold down the required preset until radio

beeps. The preset number will appear in the display

and the station will be stored under chosen preset

button.

4. Repeat this procedure for the remaining presets.

5. Stations stored in preset memories can be overwritten

by following above procedures.

Recall stations from preset

memories

1. Press the Power button to turn on the radio.

2. Select the required waveband.

3. Momentarily press the required Preset button, the

preset number and station frequency will appear in the

display.

Setting the radio alarm

When the radio alarm is selected, the radio will turn on

and play the chosen radio station at the chosen alarm

time. The radio alarm will continue for one hour unless

turned off by pressing the Power button. Pressing the

Power button whilst the alarm is activated will cancel the

alarm for 24 hours.

Note:

When the radio is in low battery status, the radio alarm

can’t be activated.

a. Setting radio alarm time:

1. The radio alarm can be set either when radio is on or

off.

2. Press and release radio alarm button , the

radio alarm symbol will flash.

3. During radio alarm symbol flashing, press button

for more than 2 seconds followed by a beep.

4. Display Hour will flash, rotate Tuning/Volume control

knob to select the hour then press button again

to confirm hour setting.

5. Follow same procedures of setting hour to set

required minute. Press button to complete alarm

time setting.

b. Setting radio alarmed station

1. During setting radio alarm time and radio alarm

symbol is flashing, press Band button to activate the

radio to select required wake-up band and station by

manual tuning and recall the preset stations. Press

button to complete radio alarm setting.

Display will show .

2. When above radio alarm time and station are set,

press and hold down radio alarm button for

2 seconds followed by a beep to switch alarm on or

off. Display will show when radio alarm is set.

Note:

If new radio alarm station is not selected, it will select

the last alarm station.

Setting the HWS (Humane Wake

System) buzzer alarm

A beep tone will activate when selecting the HWS buzzer

alarm.

The alarm beep will become shorter every 15 seconds for

one minute followed by one minute silence before

repeating the cycle.

The HWS alarm will sound for one hour until turning off by

pressing the Power button. Press the Power button whilst

the alarm is activated will cancel the alarm for 24 hours.

1. The HWS buzzer alarm can be set either radio is on or

off.

2. Press and release the HWS buzzer alarm button

, the symbol will flash.

3. During the symbol flashes, long pressing the

button for more than 2 seconds followed by a beep

and display Hour digit will flash.

4. Rotate Tuning/Volume control knob to select required

alarm hour, then press time set button again. The

minute digit will then flash.

5. Rotate Tuning/Volume control knob to select required

alarm minute, the press time set button again to

complete HWS buzzer alarm setting.

6. Press and hold down buzzer alarm button for

more than 2 seconds followed by a beep to switch on

or off the HWS buzzer alarm.

How do I set the time on my dmr107 Mikita radio
Submitted on 28-4-2022 at 11:23
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DMR107 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 8,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DMR107 Manual

Product: