Manual Makita DMR102 (page 10 of 88) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

600293

Zoom out

Zoom in

1/88

• To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge or

pressing the buttons on both sides of the cartridge.

3-2. Installing or removing Cluster battery cartridge

(Fig. 5 - 9)

• Pull the supporting bar to allow the battery to insert to

the terminal.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place.

• Release the supporting bar.

• To remove the battery cartridge, pull the supporting bar

and take the battery out of the terminal.

4. Return the battery compartment locker to the original

position.

5. Reduced power, distortion and a “stuttering sound” or

low battery sign that appears on the display are

all the signs that the main battery pack needs to

replace.

Note:

The battery pack can’t be charged via the supplied AC

power adaptor.

6. When low battery sign appears and an “E” keeps

on flashing is the time to replace the back up batteries.

Installing the Soft bended rod

antenna (Fig. 10 & 11)

Install the Soft bended rod antenna as shown in the

figure.

Note:

There is a click in the battery compartment designed to

store the removed antenna.

Using Supplied AC power adaptor

(Fig. 12)

Remove the rubber protector and insert the adaptor plug

into the DC socket on the front side of the radio. Plug the

adaptor into a standard mains socket outlet. Whenever

the adaptor is used, the battery pack is automatically

disconnected. The AC adaptor should be disconnected

from the main supply when not in use.

Note:

When your radio has any interference in AM band by its

adaptor, please move your radio away from its AC

adaptor over 30 cm.

Setting the clock

1. Clock can be set either when the radio is power on or

off.

2. Display will show “-: - -” when the back up batteries

are installed.

3. Long press the time set button for more than

2 seconds, display will flash time set symbol and

also the hour digit, followed by a beep.

4. Rotate Tuning/Volume control knob to set the required

hour.

5. Press button to confirm hour setting, the minute

digit will flash.

6. Rotate Tuning/Volume control knob to set the required

minute.

7. Press the button again to complete clock setting.

Operating the radio

This radio equips with three tuning methods - Scan tuning,

Manual tuning and Memory presets recall.

Scan Tuning

1. Press the Power button to turn on the radio.

2. Select the required waveband by pressing the Band

button. Make sure the rubber bended rod antenna has

been well placed for best FM reception. For AM (MW)

band, rotate the radio to get best signal. Try to avoid to

operate the radio next to computer screen and other

equipment which will cause interference to the radio.

3. Press and release Scan button (long press Scan

button more than 2 seconds will activate time setting),

LCD display will flash Scan symbol and the radio will

search and stop automatically when it finds a radio

station. Press the Scan button again to pick up the

found station.

Note:

A stereo symbol will appear on the display, if the

station found is a stereo station.

Note:

The radio will continue to search next available

stations if you do not press Scan button again when it

finds a radio station.

4. Rotate the Tuning/Volume control knob to get required

sound level. LCD display will show sound level

changes.

Note:

During operating volume control, you can press in

Tuning/Volume control knob to change volume control

to tuning control status.

5. To turn off the radio, press the Power button. Display

will show OFF.

Manual Tuning

1. Press the Power button to turn on the radio.

2. Select the required waveband by pressing the Band

button. Adjust the antenna as described above.

3. A single rotary to the Tuning/Volume control knob will

change the frequency in the following increment:

FM: 50 or 100 kHz

AM (MW): 9 or 10 kHz

WARNING:

Do not use two main batteries at the same time.

My radio keeps switching off then showing a symbol in screen E backwards simular to a 3.
Whats going on ?
Submitted on 26-11-2022 at 07:03
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DMR102 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DMR102 Manual

Product: