Manual Makita DLS600 (page 20 of 160) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691786

Zoom out

Zoom in

1/160

20 ENGLISH

Aligning the laser line

Align the cutting line on your workpiece with the laser

line.

►Fig.31

A) When you want to obtain the correct size on the left side

of workpiece, shift the laser line to the left of the blade.

B) When you want to obtain the correct size on the right

side of workpiece, shift the laser line to the right of the

blade.

ASSEMBLY

WARNING: Always be sure that the tool is

switched off and the battery cartridge is removed

before working on the tool. Failure to switch off and

remove the battery cartridge may result in serious

personalinjury.

Hex wrench storage

Thehexwrenchisstoredasshowninthegure.When

the hex wrench is needed it can be pulled out of the

wrench holder.

After using the hex wrench it can be stored by returning

it to the wrench holder.

►Fig.32: 1. Wrench holder 2. Hex wrench

Installing or removing saw blade

WARNING: Always be sure that the tool is

switched off and the battery cartridge is removed

before installing or removing the blade. Accidental

start up of the tool may result in serious personal

injury.

CAUTION: Use only the Makita hex wrench

provided to install or remove the blade. Failure

todosomayresultinovertighteningorinsufcient

tightening of the hex socket bolt. This could cause

aninjury.

To remove the blade, perform the following steps:

1. Release the stopper pin, and then lock the handle

in the raised position by pushing in the stopper pin.

►Fig.33: 1. Stopper pin

2. Use the hex wrench to loosen the hex socket bolt

holding the center cover by turning it counterclockwise.

Then, raise the blade guard and center cover.

►Fig.34: 1. Center cover 2. Hex socket bolt 3. Hex

wrench 4. Blade guard

3. Press the shaft lock to lock the spindle and use

the hex wrench to loosen the hex socket bolt clockwise.

Then remove the hex socket bolt of the spindle, outer

angeandblade.

►Fig.35: 1. Shaft lock 2. Hex socket bolt 3. Outer

ange

4. Iftheinnerangeisremoved,installitonthespin-

dle with its blade mounting part facing the blade. If the

angeisinstalledincorrectlytheangewillrubagainst

the machine.

►Fig.36: 1.Outerange2. Saw blade 3.Innerange

4. Hex socket bolt (left-handed) 5. Spindle

6. Blade mounting part

To install the blade, perform the following steps:

1. Mountthebladecarefullyontotheinnerange.

Make sure that the direction of the arrow on the blade

matches the direction of the arrow on the blade case.

►Fig.37: 1. Saw blade 2. Arrow

2. Installtheouterangeandhexsocketbolt,and

then use the hex wrench to tighten the hex socket bolt

(left-handed) of the spindle securely counterclockwise

while pressing the shaft lock.

3. Return the blade guard and center cover to its

original position. Then tighten the hex socket bolt of the

center cover clockwise to secure the center cover.

4. Release the handle from the raised position by

pulling the stopper pin. Lower the handle to make sure

that the blade guard moves properly.

5. Make sure the shaft lock has released spindle

before making cut.

For tool with the inner ange for

15.88 mm hole-diameter saw blade

Country specic

Mounttheinnerangewithitsrecessedsidefacing

outward onto the mounting shaft and then place saw

blade(withtheringattachedifneeded),outerange

and hex bolt.

For tool without the ring

►Fig.38: 1.Outerange2. Saw blade 3.Innerange

4. Hex socket bolt (left-handed) 5. Spindle

For tool with the ring

►Fig.39: 1.Outerange2. Saw blade 3.Innerange

4. Hex socket bolt (left-handed) 5. Ring

6. Spindle

WARNING: If the ring is needed to mount the

blade onto the spindle, always be sure that the

correct ring for the blade's arbor hole you intend

to use is installed between the inner and the outer

anges. Use of the incorrect arbor hole ring may

result in the improper mounting of the blade causing

blade movement and severe vibration resulting in

possible loss of control during operation and in seri-

ouspersonalinjury.

For tool with the inner ange for

other than 20 mm or 15.88 mm hole-

diameter saw blade

Country specic

Theinnerangehasacertaindiameterofablade

mounting part on one side of it and a different diameter

of blade mounting part on the other side. Choose a

correctsideonwhichblademountingparttsintothe

saw blade hole perfectly.

►Fig.40: 1.Outerange2. Saw blade 3.Innerange

4. Hex socket bolt (left-handed) 5. Spindle

6. Blade mounting part

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DLS600 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 32,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DLS600 Manual

Product: