Manual Makita DLS600 (page 18 of 160) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691786

Zoom out

Zoom in

1/160

18 ENGLISH

2. Re-tighten them only to the extent that the kerf

boards can still be easily moved by hand.

3. Lower the handle fully and push in the stopper pin

to lock the handle in the lowered position.

4. Adjustthekerfboardssothatthekerfboardsjust

contact the sides of the blade teeth.

►Fig.13

►Fig.14: 1. Saw blade 2. Blade teeth 3. Kerf board

4. Left bevel cut 5. Straight cut

5. Tightenthescrews(donottightenrmly).

Afteradjustingthekerfboards,releasethestopperpin

and raise the handle. Then tighten all the screws securely.

NOTICE: After setting the bevel angle ensure

that the kerf boards are adjusted properly. Correct

adjustmentofthekerfboardshelpstoprovideproper

support of the workpiece and minimizing workpiece

tear out.

Maintaining maximum cutting

capacity

Thistoolisfactoryadjustedtoprovidethemaximum

cutting capacity for a 165 mm saw blade.

When installing a new blade, always check the lower limit

positionoftheblade,andifnecessary,adjustitasfollows:

1. Remove the battery cartridge. Lower the handle

completely.

2. Usethehexwrenchtoturnthelowerlimitadjust-

ing bolt until the saw blade comes slightly below the

cross section of the guide fence and the top surface of

the turn base.

►Fig.15: 1.Adjustingbolt

►Fig.16: 1. Guide fence

3. Rotate the blade by hand while holding the handle

all the way down to be sure that the blade does not

contactanypartofthelowerbase.Re-adjustslightly,if

necessary.

WARNING: After installing a new blade and

with the battery cartridge removed, always be

sure that the blade does not contact any part of

the lower base when the handle is lowered com-

pletely. If a blade makes contact with the base it may

causekickbackandresultinseriouspersonalinjury.

►Fig.17

Sub-fence

Country specic

This tool is equipped with the sub-fence and small

sub-fences.

Sub-fence

WARNING: Always remove sub-fence when

performing bevel cuts. Failure to do so may cause

seriousinjury.

►Fig.18: 1. Sub-fence

When performing cuts except for bevel cuts, use the

sub-fence to support the workpiece.

Small sub-fence

CAUTION: When performing right bevel cuts,

fold the small sub-fences. Otherwise, they may

contact the blade or a part of the tool, and may result

inseriousinjurytotheoperator.

►Fig.19: 1. Small sub-fence 2. Scale

Whenperformingverticalcutorleftbevelcut,ipthem

upward to support the workpiece. The guide fence has

a scale of 10 mm interval.

Adjusting the miter angle

►Fig.20: 1. Fixing screw 2. Turn base 3. Miter scale

4. Pointer

1. Loosenthexingscrewcounterclockwise.

2. Adjusttheangleoftheturnbase.Usethepointer

and the miter scale as a guide.

3. Tightenthexingscrewclockwisermly.

CAUTION: After changing the miter angle,

always secure the turn base by tightening the

xing screw rmly.

NOTICE: When turning the turn base, be sure to

raise the handle fully.

Adjusting the bevel angle

Toadjustthebevelangle,turntheleverattherearof

the tool downward.

►Fig.21: 1. Lever

To tilt the blade to the left, hold the handle and tilt the saw

head. Use the bevel scale and the pointer as a guide.

Thenturntheleverupwardrmlytosecurethesawhead.

►Fig.22: 1. Pointer 2. Bevel scale

To tilt the blade to the right, hold the handle and tilt the

saw head to the left slightly, and push the release button.

With the release button pressed, tilt the saw blade to the

right.Turntheleverupwardrmlytosecurethesawhead.

►Fig.23: 1. Release button

CAUTION: After changing the bevel angle,

always secure the saw head by turning the lever

upward rmly.

NOTICE: When tilting the saw blade, be sure the

handle is fully raised.

NOTICE: When changing bevel angles, be

sure to position the kerf boards appropriately

as explained in the "Positioning kerf boards"

section.

Setting 46° bevel angle

1. Loosen the lever and tilt the blade to the left or

right fully.

►Fig.24: 1. Lever

2. To tilt the blade to the left, hold the handle and tilt

the saw head to the right slightly, and then move the

release lever to the direction of the arrow. The bevel

anglecanbeadjustedbetween45°to46°bytiltingthe

saw head while moving the release lever.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DLS600 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 32,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DLS600 Manual

Product: