Manual Makita DLS600 (page 14 of 160) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691786

Zoom out

Zoom in

1/160

14 ENGLISH

14. Always use a clamp or a xture designed to

properly support round material such as rods

or tubing. Rods have a tendency to roll while

being cut, causing the blade to "bite" and pull the

work with your hand into the blade.

15. Let the blade reach full speed before contact-

ing the workpiece. This will reduce the risk of the

workpiece being thrown.

16. If the workpiece or blade becomes jammed,

turn the mitre saw off. Wait for all moving

parts to stop and disconnect the plug from

the power source and/or remove the battery

pack. Then work to free the jammed material.

Continuedsawingwithajammedworkpiececould

cause loss of control or damage to the mitre saw.

17.

After nishing the cut, release the switch, hold

the saw head down and wait for the blade to stop

before removing the cut-off piece. Reaching with

your hand near the coasting blade is dangerous.

18.

Hold the handle rmly when making an incom-

plete cut or when releasing the switch before the

saw head is completely in the down position. The

braking action of the saw may cause the saw head to

besuddenlypulleddownward,causingariskofinjury.

19. Only use the saw blade with the diameter that

is marked on the tool or specied in the man-

ual. Use of an incorrectly sized blade may affect

the proper guarding of the blade or guard opera-

tionwhichcouldresultinseriouspersonalinjury.

20.

Only use the saw blades that are marked with a speed

equal or higher than the speed marked on the tool.

21. Do not use the saw to cut other than wood,

aluminum or similar materials.

22. (For European countries only)

Always use the blade which conforms to EN847-1.

Additional instructions

1. Make workshop kid proof with padlocks.

2. Never stand on the tool.Seriousinjurycould

occur if the tool is tipped or if the cutting tool is

unintentionally contacted.

3. Never leave the tool running unattended. Turn

the power off. Do not leave tool until it comes

to a complete stop.

Do not operate saw without guards in place.

Check blade guard for proper closing before

each use. Do not operate saw if blade guard does

not move freely and close instantly. Never clamp

or tie the blade guard into the open position.

5. Keep hands out of path of saw blade. Avoid

contact with any coasting blade. It can still

cause severe injury.

6. Always secure all moving portions before

carrying the tool.

7. Stopper pin which locks the cutter head down

is for carrying and storage purposes only and

not for any cutting operations.

Check the blade carefully for cracks or damage

before operation. Replace cracked or damaged

blade immediately. Gum and wood pitch hardened

on blades slows saw and increases potential for

kickback. Keep blade clean by rst removing it from

tool, then cleaning it with gum and pitch remover, hot

water or kerosene. Never use gasoline to clean blade.

9. Use only anges specied for this tool.

10. Be careful not to damage the arbor, anges

(especially the installing surface) or bolt.

Damage to these parts could result in blade

breakage.

11. Make sure that the turn base is properly

secured so it will not move during operation.

Use the holes in the base to fasten the saw to a

stable work platform or bench. NEVER use tool

where operator positioning would be awkward.

12. Make sure the shaft lock is released before the

switch is turned on.

13. Be sure that the blade does not contact the

turn base in the lowest position.

14. Hold the handle rmly. Be aware that the saw

moves up or down slightly during start-up and

stopping.

15. Make sure the blade is not contacting the

workpiece before the switch is turned on.

16. Before using the tool on an actual workpiece,

let it run for a while. Watch for vibration or

wobbling that could indicate poor installation

or a poorly balanced blade.

17. Stop operation immediately if you notice any-

thing abnormal.

18. Do not attempt to lock the trigger in the "ON"

position.

19. Always use accessories recommended in this

manual. Use of improper accessories such as

abrasive wheels may cause an injury.

20. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier

safety data.

Additional safety rules for the laser

1. LASER RADIATION, DO NOT STARE INTO THE

BEAM OR VIEW DIRECTLY WITH OPTICAL

INSTRUMENTS, CLASS 2M LASER PRODUCT.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DLS600 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 32,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DLS600 Manual

Product: