Manual Makita DLS600 (page 13 of 160) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691786

Zoom out

Zoom in

1/160

13 ENGLISH

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN62841:

Vibration emission (a

) : 2.5 m/s

or less

Uncertainty (K) : 1.5 m/s

NOTE:

The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

NOTE:

The declared vibration emission value may

also be used in a preliminary assessment of exposure.

WARNING:

The vibration emission during actual

use of the power tool can differ from the declared emission

value depending on the ways in which the tool is used.

WARNING: Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it is

running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING:

Read all safety warnings, instruc-

tions, illustrations and specications provided with this

power tool. Failure to follow all instructions listed below

mayresultinelectricshock,reand/orseriousinjury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Safety instructions for mitre saws

1. Mitre saws are intended to cut wood or wood-

like products, they cannot be used with abra-

sive cut-off wheels for cutting ferrous material

such as bars, rods, studs, etc. Abrasive dust

causes moving parts such as the lower guard to

jam.Sparksfromabrasivecuttingwillburnthe

lower guard, the kerf insert and other plastic parts.

Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand,

you must always keep your hand at least 100

mm from either side of the saw blade. Do not

use this saw to cut pieces that are too small to

be securely clamped or held by hand. If your

hand is placed too close to the saw blade, there is

anincreasedriskofinjuryfrombladecontact.

3. The workpiece must be stationary and

clamped or held against both the fence and the

table. Do not feed the workpiece into the blade

or cut "freehand" in any way. Unrestrained

or moving workpieces could be thrown at high

speeds,causinginjury.

Never cross your hand over the intended line of

cutting either in front or behind the saw blade.

Supporting the workpiece "cross handed" i.e.

holding the workpiece to the right of the saw blade

with your left hand or vice versa is very dangerous.

►Fig.1

5. Do not reach behind the fence with either hand

closer than 100 mm from either side of the saw

blade, to remove wood scraps, or for any other

reason while the blade is spinning. The proxim-

ity of the spinning saw blade to your hand may not

beobviousandyoumaybeseriouslyinjured.

6. Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with

the outside bowed face toward the fence.

Always make certain that there is no gap

between the workpiece, fence and table along

the line of the cut. Bent or warped workpieces

can twist or shift and may cause binding on the

spinning saw blade while cutting. There should be

nonailsorforeignobjectsintheworkpiece.

7. Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the work-

piece. Small debris or loose pieces of wood or

otherobjectsthatcontacttherevolvingbladecan

be thrown with high speed.

Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

9. Ensure the mitre saw is mounted or placed on

a level, rm work surface before use. A level

andrmworksurfacereducestheriskofthemitre

saw becoming unstable.

10. Plan your work. Every time you change the

bevel or mitre angle setting, make sure the

adjustable fence is set correctly to support the

workpiece and will not interfere with the blade

or the guarding system. Without turning the tool

"ON" and with no workpiece on the table, move

the saw blade through a complete simulated cut to

assure there will be no interference or danger of

cutting the fence.

11. Provide adequate support such as table exten-

sions, saw horses, etc. for a workpiece that is

wider or longer than the table top. Workpieces

longer or wider than the mitre saw table can tip

if not securely supported. If the cut-off piece or

workpiece tips, it can lift the lower guard or be

thrown by the spinning blade.

12.

Do not use another person as a substitute for a

table extension or as additional support. Unstable

support for the workpiece can cause the blade to bind

or the workpiece to shift during the cutting operation

pulling you and the helper into the spinning blade.

13. The cut-off piece must not be jammed or

pressed by any means against the spinning

saw blade.Ifconned,i.e.usinglengthstops,the

cut-off piece could get wedged against the blade

and thrown violently.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DLS600 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 32,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DLS600 Manual

Product: