Manual Makita DLS111 (page 30 of 244) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691782

Zoom out

Zoom in

1/244

30 ENGLISH

Crown molding stopper

Optional accessory

Crown molding stoppers allow easier cuts of crown

molding without tilting the saw blade. Install them on the

turnbaseasshowninthegures.

At right 45° miter angle

►Fig.52: 1. Crown molding stopper L 2. Crown mold-

ing stopper R 3.Turnbase4. Guide fence

At left 45° miter angle

►Fig.53: 1. Crown molding stopper L 2. Crown mold-

ing stopper R 3.Turnbase4. Guide fence

PositioncrownmoldingwithitsWALLCONTACTEDGE

againsttheguidefenceanditsCEILINGCONTACTEDGE

againstthecrownmoldingstoppersasshowninthegure.

Adjustthecrownmoldingstoppersaccordingtothesizeof

thecrownmolding.Tightenthescrewstosecurethecrown

molding stoppers. Refer to the table (C) for the miter angle.

►Fig.54: 1. Guide fence 2. Crown molding stopper

(a) (b) (c) (d)

1. Inside corner 2. Outside corner

Table (C)

– Molding

position in

the gure

Miter angle Finished

piece

For inside

corner

(a) Right 45° Save the right

side of blade

(b) Left 45° Save the left

side of blade

For outside

corner

side of blade

(d) Right 45° Save the left

side of blade

Cutting aluminum extrusion

►Fig.55: 1. Vise 2. Spacer block 3. Guide fence

4.Aluminumextrusion5. Spacer block

When securing aluminum extrusions, use spacer blocks or pieces

ofscrapasshownintheguretopreventdeformationofthealu-

minum. Use a cutting lubricant when cutting the aluminum extru-

sion to prevent build-up of the aluminum material on the blade.

WARNING: Never attempt to cut thick or

round aluminum extrusions.Thickorroundalumi-

numextrusionscanbedifculttosecureandthework

may loosen during the cutting operation which may

resultinlossofcontrolandseriouspersonalinjury.

Groove cutting

WARNING: Do not attempt to perform this

type of cut by using a wider type blade or dado

blade.Attemptingtomakeagroovecutwithawider

blade or dado blade could lead to unexpected cutting

results and kickback which may result in serious

personalinjury.

WARNING: Be sure to return the stopper arm

to the original position when performing other

than groove cutting.Attemptingtomakecutswith

the stopper arm in the incorrect position could lead to

unexpected cutting results and kickback which may

resultinseriouspersonalinjury.

For a dado type cut, perform as follows:

1. Adjustthelowerlimitpositionofthebladeusing

theadjustingscrewandthestopperarmtolimitthecut-

tingdepthoftheblade.Referto"Stopperarm"section

described on previously.

2. Afteradjustingthelowerlimitpositionoftheblade,

cut parallel grooves across the width of the workpiece

using a slide (push) cut.

►Fig.56: 1. Cut grooves with blade

3. Remove the workpiece material between the

grooves with a chisel.

Carrying tool

Before carrying, make sure to remove the batteries and

allmovablepartsofthemitersawaresecured.Always

check the following:

• Thebatteriesareremoved.

• Thecarriageisat0°bevelanglepositionand

secured.

• Thecarriageisloweredandlocked.

• Thecarriageisfullyslidtotheguidefenceand

locked.

• Theturnbaseisatthefullrightmiterangleposi-

tion and secured.

• Theholdersarestoredandsecured.

Carry the tool by holding both sides of the tool base as

showninthegure.

►Fig.57

WARNING: Stopper pin for carriage elevation

is for carrying and storage purposes only and not

for any cutting operations.Theuseofthestopper

pin for cutting operations may cause unexpected

movement of the saw blade resulting in kickback and

seriouspersonalinjury.

CAUTION: Always secure all moving portions

before carrying the tool. If portions of the tool move

or slide while being carried, loss of control or balance

mayoccurandresultinpersonalinjury.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DLS111 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 37,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DLS111 Manual

Product: