600450
7
Zoom out
Zoom in
Previous page
1/60
Next page
7
011058
Note: These values can be changed on PC (except for DFT041R). Refer to SRCV02 USER MANUAL for details.
For LED#B (Fig. 6)
Led indicator / Beeper on the tool shows the following functions.
007929
Note 1: Refer to a instruction manual of receiver (acces-
sory) RCV02 when connecting it.
Note 2: Communication distance: 10 m or less (variable
up to 10 m depending on the operation environment)
CAUTION:
Make sure that LED#B (2) does not light up before
removing a battery cartridge from the tool. If a battery
cartridge is removed while LED#B (2) lights up or
blinks, tools stored data will be deleted.
Adjusting the fastening torque (Fig. 7 & 8)
When you wish to drive machine screws, wood screws,
hex bolts, etc. with the predetermined torque, adjusting
the fastening torque as follows.
1. First remove the battery cartridge from the tool.
2. Loosen and remove the screw that secures ring.
3. Rotate the ring in the front of the tool by hand so that a
hole can be seen below the ring.
Status of
the LED indicator/beeper
Function Status Action to be taken
LED indicator Beeper
Blinks in red
and yellow
alternatively.
A long beep
Warning against
insufficient
fastening
Fastening is incomplete when switch
trigger of tool is released before clutch
activation.
__
Double-hitting
detection
This function works when a screw is
refastened after fastening.
__
Angle judge NOK
This function works when a screw is not
fastened within the angle range preset
on PC (Note).
__
Rundown NOK
This function works when a fastening is
finished before it reaches the preset
angle range. (Note)
__
Torque impossible
monitoring
This function works when torque
monitoring is cannot be carried out.
__
Blinks in red
and blue
alternatively.
A series of
short beeps
Disconnection
(when using
receiver RCV02)
Radio communication not yet
established
Finish necessary
connection or remove
a battery cartridge to
escape.
Radio
communication
failure
This function works when there is radio
communication failure.
Take it to a Makita
Authorized Service
centers.
Description Viewed color View and status
LED#B (1) Green
1 lights up when the tool is connected to a receiver.
2blinks
when the tool is on the step of being connected to a
receiver. (Note 1)
3 is turned off
one of the status below
3-1 when the battery cartridge is removed from the tool.
3-2
when the tool is left idle for more than 15 minutes
with a installed battery cartridge.
3-3
when the tool is not within the transmission dis-
tance. (Note 2)
LED#B (2) Red
1 lights up
when the tool’s stored number of data reaches its storable
number of data.
2blinks
when the tool’s stored number of data is equal to or smaller
than its storable number of data.
3 is turned off when the tool has no stored data to transmit to a receiver.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DFT124R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DFT124R in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info