793613
10
Zoom out
Zoom in
Previous page
1/124
Next page
10 ENGLISH
Error code
and status
symbol on
screen
Tool performance
and function
Tool status LED indicators/beeper status Action to be taken
LED indicators Beeper
-󰀩
fastening
The tool raises an alert for
incomplete fastening under the
following operating conditions.
(1): The trigger switch is
released before the pre-set
fastening torque has been
achieved.
(2): The tool stops automati-
cally after classifying fastening
errors.
(1): The LED
indicator lights
up in red for
approximately two
seconds.
(2): The LED

in yellow and red
alternately for
approximately two
seconds.
A long
beep
Retighten the screw.
Waiting function
between pre-set
fastening steps
The tool is sitting idle, after one
of the pre-set fastening steps
has been completed, waiting to
follow the next pre-set fasten-
ing step.
* A status symbol ( 
in the display screen.
The LED indicator
lights up in green.
- -
-Low-battery alert The battery is becoming low on
power, and the battery cartridge
needs to be recharged or
replaced with fully charged one.
The LED indicator

in red.
A series of
long beeps
Replace the battery
with fully charged
one.
-Error alert for heat
detection of motor
The motor temperature cannot
be monitored properly for a
number of technical reasons
including line breaks.
The LED indicator

in red.
A series
of short
beeps
Remove the battery
cartridge and cool
the tool down. If the
indicator remains lit,
ask your local Makita
Service Center for
repair.
Maintenance notice Maintenance notice will be
posted for optimum operational
reliability when the accu-
mulated maintenance count
reaches the pre-set number.
* A status symbol ( )
appears in the display screen
when the accumulated mainte-
nance count reaches the pre-
set “Stop Count” number.
The LED indicator

-Reset the mainte-
nance count in the
application software
designed for this
tool.
Alert for storage
disabled
Up to 1,000 fastening result
data can be saved in the tool
memory. The number of unread
data in the memory reaches to
the maximum.
* A status symbol ( )
appears in the display screen
when the storage capacity
reaches the maximum.
The LED indicator

-Load the fastening
result data saved
in the tool memory
using the application
software designed
for this tool.
-Error alert for data
communication with
computer
The tool raises an alert for
communication error in the
wired environment.
The LED indicator

-Link the tool again
with the application
software designed
for the tool after
restarting the
application.
-Status indicator for
data communication
with computer
The tool informs that data
communication has been
securely established in the
wired environment.
The LED indicator

- -
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DFT060T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DFT060T in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 18.78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info