Manual Makita DFL125F (page 8 of 80) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691569

Zoom out

Zoom in

1/80

8 ENGLISH

Function Status of the tool Status of the LED indicator/beeper Action to be taken

LED indicator Beeper

Motor failure detection Motor failure has been

detected. At this time,

tool does not work.

Flickers in red and green

alternatively.

A series of short beeps Ask your local Makita

Service Center for repair.

Double-hitting detection When the operator

starts to re-fasten an

already-fastened screw,

the tool detect it and

stops.

Lights up in red. A long beep –

Maintenance alarm A maintenance time has

come according to your

preset number of screws

driven.

Flickers in yellow. – Reset the alarm with the

application software.

Alarm for unavailable

data communication

(with the tool in connec-

tion with PC)

Data cannot be

exchanged between the

tool and PC in spite of

the connection.

Flickers in yellow. – Restart the application

software and re-connect

the USB cable.

Indication that data com-

munication is available

(with the tool in connec-

tion with PC)

The tool is connected to

PC and data communi-

cation is available.

Flickers in green. – –

Adjusting the fastening torque

When you wish to drive machine screws, hex bolts,

etc. with the predetermined torque, adjust the fastening

torque as follows.

1. First remove the battery cartridge from the tool.

2. Loosen and remove the screw that secures the

ring and lamp cover.

►Fig.7: 1. Screw 2. Lamp cover

3. Rotate the ring in the front of the tool by hand so

that a hole can be seen below the ring.

►Fig.8: 1. Ring

4. Install the battery cartridge in place. Pull the

switch trigger and release it so that the adjust ring

rotates and the hole becomes visible. And then remove

the battery cartridge.

►Fig.9: 1. Adjust ring 2. Hole for adjust grip

5. Use an optional adjust grip to adjust the fastening

torque. Insert the pin of the adjust grip into the hole

in the front of the tool. And then, turn the adjust grip

clockwise to set a greater fastening torque, and coun-

terclockwise to set a smaller fastening torque.

6. Align the yellow line with your desired number on

the fastening torque scale.

►Fig.10: 1. Adjust grip 2. Hole for adjust grip 3. Scale

4. Yellow line

7. Insert the battery cartridge and be sure that a

fastening torque has been set up by using a fastening

torque tester.

8. Rotate the ring in front of the tool and then tighten

the screw to secure the ring and lamp cover.

NOTE: Numbers on the fastening torque scale is a

guideline to set up your desired fastening torque.

Adjusting no-load speed and

revolution angle etc.

You can adjust the no-load speed, number of turn, etc.

of the tool with your computer. Install the application

software in your computer and connect it to the tool with

an USB cable.

►Fig.11: 1. USB cable 2. USB cover 3. USB port

NOTICE: Make sure that the USB cover closed

when fastening.

NOTE: For the application software, please contact

Makita sales representative.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Selecting correct socket

There are different types of sockets for some models

depending on applications. Choose and install a correct

socket for your application.

Installing or removing socket

►Fig.12: 1. Socket 2. Hole 3. Pin

To install the socket, push it onto the square drive of the

tool with one hand by depressing a pin on the square

drive with another hand until it locks into place. To

remove the socket, simply pull it off depressing the pin

on the square drive.

CAUTION: Before operation, make sure that

the socket is properly locked onto the square

drive. Incomplete attachment of the socket may

cause injury.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DFL125F in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 10,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DFL125F Manual

Product: