Manual Makita DFL125F (page 7 of 80) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691569

Zoom out

Zoom in

1/80

7 ENGLISH

Switch action

WARNING: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

►Fig.3: 1. Switch trigger

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop.

Reversing switch action

►Fig.4: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

direction of rotation before the tool stops may dam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the

A side for clockwise rotation or from the B side for coun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion, the switch trigger cannot be pulled.

Lighting up the front lamp

►Fig.5: 1. Lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

The lamp goes out approximately 10 seconds after

releasing the switch trigger.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

LED indicator / Beeper

►Fig.6: 1. LED indicator

LED indicator / Beeper on the tool shows the following functions.

Function Status of the tool Status of the LED indicator/beeper Action to be taken

LED indicator Beeper

Auto-stop with fastening

completion

The preset fasten-

ing torque has been

achieved and the tool

has stopped.

Lights up in green for

approximately one

second.

– –

Alarmagainstinsuf-

cient fastening

The preset fastening

torque has not been

achieved, because

the switch trigger has

released before complet-

ing the fastening.

Lights up in red. A long beep Retighten the screw.

Alarm for low battery

capacity

The battery power

became low and it is

time to replace the

battery cartridge.

Flickers in red slowly. A series of long beeps Replace the battery with

fully charged one.

Auto-stop with low

remaining battery

capacity

The battery power is

almost used up and the

tool stopped.

Lights up in red. A long beep Replace the battery with

fully charged one.

Check of the LED indi-

cator, light and beeper

operation

When the battery

cartridge is installed,

the tool checks for its

LED indicator, light and

beeper.

Lightsuprstingreen,

next red.

(And then the light

comes on.)

A series of very short

beeps

–

Anti-reset of controller The battery voltage

dropped abnormally for

some reason, and the

tool stopped.

Flickers in red and green

alternatively.

A series of short beeps Replace the battery with

fully charged one.

Overheat protection Tool's controller heated

up abnormally and the

tool stopped.

Flickers in red quickly. A series of short beeps Remove the battery car-

tridge immediately and

cool the tool down.

Detection of switch

trigger operation when

installing battery

When the battery car-

tridge is installed with

the switch trigger pulled,

the tool stops to avoid

unintentional start.

Flickers in red and green

alternatively.

A series of short beeps Release the switch

trigger.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DFL125F in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 10,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DFL125F Manual

Product: