Manual Makita DF332DSAJ (page 9 of 72) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

711023

Zoom out

Zoom in

1/72

9 ENGLISH

Toremovethedriverbit,pullthesleeveinthedirection

ofthearrowandpullthedriverbitout.

NOTE:Ifthedriverbitisnotinserteddeepenough

intothesleeve,thesleevewillnotreturntoitsoriginal

positionandthedriverbitwillnotbesecured.Inthis

case,tryre-insertingthebitaccordingtotheinstruc-

tionsabove.

NOTE:Afterinsertingthedriverbit,makesurethatit

isrmlysecured.Ifitcomesout,donotuseit.

Installing hook

►Fig.12: 1. Groove 2. Hook 3. Screw

Thehookisconvenientfortemporarilyhangingthetool.

Thiscanbeinstalledoneithersideofthetool.Toinstall

thehook,insertitintoagrooveinthetoolhousingon

eithersideandthensecureitwithascrew.Toremove,

loosenthescrewandthentakeitout.

Installing driver bit holder

Optional accessory

►Fig.13: 1.Driverbitholder2.Driverbit

Fitthedriverbitholderintotheprotrusionatthetoolfoot

oneitherrightorleftsideandsecureitwithascrew.

Whennotusingthedriverbit,keepitinthedriverbit

holders.Driverbits45mm-longcanbekeptthere.

OPERATION

CAUTION: Always insert the battery cartridge

all the way until it locks in place.Ifyoucansee

theredpartontheuppersideofthebutton,itisnot

lockedcompletely.Insertitfullyuntiltheredpartcan-

notbeseen.Ifnot,itmayaccidentallyfalloutofthe

tool,causinginjurytoyouorsomeonearoundyou.

CAUTION: When the speed comes down

extremely, reduce the load or stop the tool to

avoid the tool damage.

Holdthetoolrmlywithonehandonthegripandthe

otherhandonthebottomofthebatterycartridgeto

control the twisting action.

►Fig.14

Screwdriving operation

CAUTION: Adjust the adjusting ring to the

proper torque level for your work.

CAUTION: Make sure that the driver bit is

inserted straight in the screw head, or the screw

and/or driver bit may be damaged.

Placethepointofthedriverbitinthescrewheadand

applypressuretothetool.Startthetoolslowlyandthen

increasethespeedgradually.Releasetheswitchtrigger

assoonastheclutchcutsin.

NOTE: When driving wood screw, pre-drill a pilot hole

2/3thediameterofthescrew.Itmakesdrivingeasier

andpreventssplittingoftheworkpiece.

Drilling operation

First,turntheadjustingringsothatthepointerpointsto

the marking.Thenproceedasfollows.

Drilling in wood

Whendrillinginwood,thebestresultsareobtained

withwooddrillsequippedwithaguidescrew.Theguide

screwmakesdrillingeasierbypullingthedrillbitinto

the workpiece.

Drilling in metal

Topreventthedrillbitfromslippingwhenstartinga

hole,makeanindentationwithacenter-punchand

hammeratthepointtobedrilled.Placethepointofthe

drillbitintheindentationandstartdrilling.

Useacuttinglubricantwhendrillingmetals.Theexcep-

tionsareironandbrasswhichshouldbedrilleddry.

CAUTION: Pressing excessively on the tool

will not speed up the drilling.Infact,thisexcessive

pressurewillonlyservetodamagethetipofyourdrill

bit,decreasethetoolperformanceandshortenthe

servicelifeofthetool.

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece.Thereisatremendousforceexertedon

thetool/drillbitatthetimeofholebreakthrough.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure small workpieces

in a vise or similar hold-down device.

CAUTION: If the tool is operated continuously

until the battery cartridge has discharged, allow

the tool to rest for 15 minutes before proceeding

with a fresh battery.

Using the tool as a hand screwdriver

►Fig.15

Switchoffthetool.

Movethereversingswitchlevertotheneutralposition.

Turntheadjustingringsothatthearrowpointsto

the

marking.

Turnthetool.

NOTE:Thisuseisconvenientforcheckingthe

screwdriving.

NOTE:Donotusethetoolforworkrequiringexces-

siveforce,suchastighteningboltorremovingrusted

screws.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DF332DSAJ in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 14,29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DF332DSAJ Manual

Product: