Manual Makita DF332DSAJ (page 8 of 72) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

711023

Zoom out

Zoom in

1/72

8 ENGLISH

Thistoolhasareversingswitchtochangethedirection

ofrotation.Depressthereversingswitchleverfromthe

AsideforclockwiserotationorfromtheBsideforcoun-

terclockwise rotation.

Whenthereversingswitchleverisintheneutralposi-

tion,theswitchtriggercannotbepulled.

Speed change

►Fig.6: 1. Speed change lever

CAUTION:

Always set the speed change lever

fully to the correct position.Ifyouoperatethetoolwith

thespeedchangeleverpositionedhalfwaybetweenthe

"1"sideand"2"side,thetoolmaybedamaged.

CAUTION: Do not use the speed change lever

while the tool is running.Thetoolmaybedamaged.

Position of

speed

change lever

Speed Torque Applicable

operation

1 Low High Heavy load-

ing operation

2 High Low Light loading

operation

Tochangethespeed,switchoffthetoolrst.Select

the"2"sideforhighspeedor"1"forlowspeedbuthigh

torque.Besurethatthespeedchangeleverissettothe

correctpositionbeforeoperation.

Ifthetoolspeediscomingdownextremelyduringthe

operationwith"2",slidethelevertothe"1"andrestart

the operation.

Adjusting the fastening torque

►Fig.7: 1.Adjustingring2.Graduation3.Arrow

Thefasteningtorquecanbeadjustedin21stepsbyturningtheadjustingring.Alignthegraduationswiththearrow

onthetoolbody.Youcangettheminimumfasteningtorqueat1andmaximumtorqueat

marking.

Theclutchwillslipatvarioustorquelevelswhensetatthenumber1to20.Theclutchdoesnotworkat

the marking.

Beforeactualoperation,driveatrialscrewintoyourmaterialorapieceofduplicatematerialtodeterminewhich

torquelevelisrequiredforaparticularapplication.

Thefollowingshowstheroughguideoftherelationshipbetweenthescrewsizeandgraduation.

Graduation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Machine screw M4 M5 M6

Wood

screw

Softwood

(e.g. pine)

– ɸ3.5 x 22 ɸ4.1x 38 –

Hard wood

(e.g.lauan)

– ɸ3.5 x 22 ɸ4.1x 38 –

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/

drill bit

For Model DF332D (optional accessory)

►Fig.8: 1. Sleeve 2. Close 3. Open

Turnthesleevecounterclockwisetoopenthechuck

jaws.Placethedriverbit/drillbitinthechuckasfar

asitwillgo.Turnthesleeveclockwisetotightenthe

chuck.Toremovethedriverbit/drillbit,turnthesleeve

counterclockwise.

Installing or removing driver bit/

socket bit

For Model DF032D (optional accessory)

►Fig.9

Useonlydriverbit/socketbitthathasinsertingportionshown

inthegure.Donotuseanyotherdriverbit/socketbit.

For tool with shallow driver bit hole

A=12mm

B=9mm

Useonlythesetypeofdriver

bit.Followtheprocedure

1. (Note) Bit-piece is not

necessary.

For tool with deep driver bit hole

A=17mm

B=14mm

Toinstallthesetypesofdriver

bits,followtheprocedure1.

A=12mm

B=9mm

Toinstallthesetypesofdriver

bits,followtheprocedure2.

(Note) Bit-piece is necessary

forinstallingthebit.

1. Toinstallthedriverbit,pullthesleeveinthedirec-

tionofthearrowandinsertthedriverbitintothe

sleeveasfarasitwillgo.

Thenreleasethesleevetosecurethedriverbit.

►Fig.10: 1.Driverbit2. Sleeve

2. Toinstallthedriverbit,pullthesleeveinthedirec-

tionofthearrowandinsertthebit-pieceanddriver

bitintothesleeveasfarasitwillgo.Thebit-piece

shouldbeinsertedintothesleevewithitspointed

endfacingin.Thenreleasethesleevetosecure

thedriverbit.

►Fig.11: 1.Driverbit2. Bit-piece 3. Sleeve

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DF332DSAJ in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 14,29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DF332DSAJ Manual

Product: