448346
13
Zoom out
Zoom in
Previous page
1/54
Next page
13
Never use waste oil
Waste oil is very dangerous for the environment.
Waste oil contains high amounts of carcinogenic substances.
The residues in the waste oil result in a high degree of wear and
tear at the oil pump and the sawing device.
In the case of damage caused by using waste oil or
unappropriate saw chain oil the product guarantee will be null
and void.
Your salesman will inform you about the use of saw chain oil.
Avoid skin and eye contacts
Mineral oil products as well as oil degrease the skin. If your skin
repeatedly comes in contact with these substances for a longer
period of time, it will desiccate. Various skin deseases may
result. In addition, allergic reactions are known.
Eyes can be irritated by contact with oil. If oil gets into your
eyes, immediately wash them with clear water. If your eyes are
still irrritated, go to see a doctor.
E
14
G
- The oil level can be controlled in the sight glass (G/14).
Lubricating the saw chain
In order to ensure sufficient lubrication of the saw chain there
must always be enough oil in the tank. Its contents (150 ml) is
sufficient for approx. 1/2 hour at continuous operation.
Important note on bio-degradable chain oils:
If you are not planning to use the saw again for an extended
period of time, empty the oil tank and put in a small amount of
regular engine oil (SAE 30),and then run the saw for a time.
This is necessary to flush out all remaining bio-degradable oil
from the oil tank, oil-feed system, chain and guide bar, as many
such oils tend to leave sticky residues over time, which can
cause damage to the oil pump or other parts.
The next time you use the saw, fill the tank with BIOTOP chain
oil again.
F
13
Refilling the oil tank
Only if the motor is switched off and the power supply plug
is pulled out
- Thoroughly clean the oil tank around the cap to prevent dirt
from entering the tank.
- Unscrew the tank cap (F/13) and fill in chain oil until it is on
a level with the bottom edge of the filler socket.
- Tightly screw on the tank cap.
- Thoroughly remove any oil that has overflown.
Adjusting the chain lubrication
Only if the motor is switched off and the power supply
plug is pulled out
The automatic oil pump can be regulated with the adjusting
screw (H/15). The adjusting screw is mounted below the clutch
cylinder in the bottom part of the case.
When delivered the oil pump is adjusted to a medium feed
quantity. For changing the quantity use the universal wrench
and carefully adjust the adjusting screw in the following way:
turn to the right to reduce the quantity
turn to the left to increase the quantity.
ATTENTION: Never unscrew further than the lug allows.
Note: After the saw has been turned off it is normal for residual
chain oil to drip from the oil feed system, the guide bar and the
chain for a time. This does
not constitute a defect!
Place the saw on a suitable surface.
H
15
Waste oil
Important!
Before operating the saw for the first time, the oil feed system
must be completely filled, until the chain oil lubricates the chain
and guide bar.
With the oil pump feed rate set to maximum this process can
take up to two minutes.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DES 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DES 300 in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 3,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita DES 300

Makita DES 300 User Manual - German, Danish - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info