Manual Makita DBN500 (page 9 of 68) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

600591

Zoom out

Zoom in

1/68

Removing jammed nails

WARNING:

• Always make sure that the trigger is released, and the

battery cartridge and nails are removed before

removing jammed nails.

Remove hex bolts they are securing the driver guide

cover with the hex wrench.

Take the jammed nails from the nail guide groove that has

appeared.

Secure the driver guide cover with hex bolts in the correct

order. Tighten the hex bolt A, B and then C. (Fig. 16)

NOTE:

• After securing the driver guide cover, always make sure

that the driver guide cover actuates properly. If it does

not actuate properly, remove hex bolts and install the

driver guide cover again.

Nails (Fig. 17)

Handle nails and their box carefully. If the nails have been

handled roughly, they may be out of shape or their

connector breaks, causing poor nail feed.

Avoid storing nails in a very humid or hot place or place

exposed to direct sunlight. (Fig. 18)

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge and nails are removed before

attempting to perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Cleaning of magazine

When the pusher in the magazine does not move

smoothly because of dust, sand, chips or other foreign

matters, clean the magazine.

To remove the slide door, loosen the hex bolt on the

magazine. (Fig. 19)

Pull the pusher from the slide door and then remove the

stopper, sleeves and springs.

After cleaning, install the whole parts into the slide door.

To install them, take the following procedure. (Fig. 20)

1. Install the large spring into the slide door.

2. Install the parts onto the pusher in the correct order,

sleeve, small spring and then stopper.

3. Install the pusher with the other parts onto the slide

door.

NOTE:

• When you pull out the pusher from the slide door, the

parts in the slide door may bounce out.

• When you install the pusher with the other parts to the

slide door, make slight spaces between the pusher and

sleeves.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Nails

• Makita genuine battery and charger

• Safety goggles

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ from

country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 79 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection.

Vibration

ENG904-2

The vibration total value determined according to

EN60745:

Vibration emission (a

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

For European countries only

ENH003-14

EC Declaration of Conformity

We Makita Corporation as the responsible

manufacturer declare that the following Makita

machine(s):

Designation of Machine:

Cordless Brad Nailer

Model No./Type: DBN500

are of series production and

Conforms to the following European Directives:

2006/42/EC

And are manufactured in accordance with the following

standards or standardised documents:

EN60745, EN792

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DBN500 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DBN500 Manual

Product: