Manual Makita DBN500 (page 8 of 68) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

600591

Zoom out

Zoom in

1/68

ASSEMBLY

CAUTION:

• Always make sure that your fingers are not placed on

the trigger, and the battery cartridge and nails are

removed before carrying out any work on the nailer.

Loading or unloading the nails

CAUTION:

• Always make sure that your fingers are not placed on

the trigger and the battery cartridge is removed before

loading nails.

• Do not abruptly slide the slide door of the nailer loaded

with nails. Accidentally dropping nails especially when

working in high places may cause personal injuries.

• Load nails in the correct direction. Loading in wrong

direction may cause premature wear and tear of the

driver and damage of the other parts.

• Do not use deformed connected nails. Use nails

specified in this manual. Using nails other than those

specified may cause nail jamming and breakage of the

nailer.

Press the lock lever and open the slide door of the

magazine. (Fig. 8)

Set the nail strip so that the nail tips touch the bottom of

the magazine slit and slide the nail strip toward the firing

opening.

Return the slide door to the original position until the lock

lever locks it.

To remove the nails, press the lock lever and slide the

slide door. Take out nails from the magazine slit. (Fig. 9)

Nose adapter

CAUTION:

• Always make sure that your fingers are not placed on

the trigger, and the battery cartridge and nails are

removed before installing the nose adapter. (Fig. 10)

When firing nails on the material to be fastened with

easily-marred surfaces, use the nose adapter. To install

the nose adapter, place it over the center plate so that the

protrusion inside the nose adapter fits to the slit in the

driver guide cover.

When not in use, store the nose adapter in the holder at

the back end of the slide door to keep it from being lost.

Total two nose adapters can be stored.

Hook

CAUTION:

• Always make sure that your fingers are not placed on

the trigger, and the battery cartridge and nails are

removed before using the hook.

• Do not hang the hook from the waist belt. Dropping the

nailer, which is caused by the hook accidentally coming

out of place, may cause misfiring and personal injuries.

(Fig. 11)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool

housing on either side and then secure it with a screw. To

remove, loosen the screw and then take it out. (Fig. 12)

Hex wrench storage (Fig. 13)

When not in use, store the hex wrench as shown in the

figure to keep it from being lost.

OPERATION

Inspecting trigger function

CAUTION:

• Make sure that the trigger function is in working order

before each operation. If you find issues described

below, ask Makita Authorized Service Centers for

repairs.

• Before installing the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

The tool must not operate only by pulling the trigger or

only by placing the contact element against the work

piece.

Driving nails

CAUTION:

• Always be sure to first place the contact element

against the workpiece before pulling the trigger.

Select the nailing mode by pressing the mode selecting

button as mentioned in the section “Nailing mode

selection”.

Intermittent nailing (sequential mode) (Fig. 14)

To drive a nail, set the lock button to the “FREE” position.

Place the contact element against the workpiece and pull

the trigger. Release the trigger after each operation.

Continuous/intermittent nailing (continuous mode)

(Fig. 15)

When the tool is set to continuous mode, you can operate

either continuous or intermittent nailing.

To drive a nail, set the lock button to the “FREE” position.

- For continuous nailing, pull the trigger first and then

place the contact element against the workpiece. For

the next actuation, you do not need to release the

trigger.

- For intermittent nailing, place the contact element

against the workpiece and pull the trigger. For the next

actuation, you need to reset the trigger first.

NOTE:

• This tool stops automatically under the following

conditions:

- If you release the trigger or contact element from

workpiece before the tool finishes the operation

completely.

In this situation, pull the trigger again until the tool turns

into standby.

- When keep either pulling the trigger or placing the

contact element about 5 seconds without another

action.

In this case, release the trigger or the contact element

from workpiece to restart the operation.

Anti dry fire mechanism

This tool is equipped with an anti dry fire mechanism. It

automatically stops driving nails when the remaining nails

finish. In this case, load more nails to resume operation.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DBN500 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DBN500 Manual

Product: