598664

Makita BTP141 Manual

8
Zoom out
Zoom in
Previous page
1/84
Next page
8
Changing the impact force (impact driver mode “ ”) (Fig. 9)
The impact force can be changed in three steps: hard,
medium and soft.
This allows a tightening suitable to the work.
Every time the button is pressed, the impact force
grade changes in three steps.
For approximately one minute after releasing the switch
trigger, the impact force can be changed.
NOTE:
• During the operation of switch trigger, the impact force
grade cannot be changed.
Changing the torque setting (screwdriver mode
“”)
The fastening torque can be adjusted by pressing the
button in screwdriver mode.
The numbers on the LED display shows torque setting.
The fastening torque is minimum at the number 1 and
maximum at the number 9. The indication “P” is a special
mode for fastening self drilling screws.
Every time the button is pressed, the torque setting
changes from 1 to 9 and P, and then returns to 1.
The torque setting changes fast by keeping pressing the
button.
P mode is suitable for fastening self drilling screws into
steel plates in the following conditions.
• With speed change lever at “2” side, fastening max.
4 mm screw into total max. 3.2 mm steel plates.
• With speed change lever at “1” side, fastening max.
5 mm screw.
Before an actual operation, drive a trial screw into your
material or a piece of duplicate material to determine
which torque level is required for a particular application.
First, try to fasten the screw at “1”. Then increase the
number to continue fastening. Hold the tool firmly during
operation.
CAUTION:
• Don't fasten the machine screw on P mode. It may twist
your wrist suddenly and result in personal injury.
NOTE:
• Make sure to check the number on LED display before
operation. If the number is not indicated, contact your
nearest Makita service center.
• When the remaining battery capacity gets low in the
screwdriver mode, the light flashes a few times when
fastening the screw completely. In this case, recharge
the battery. If you keep operating, you may not obtain
the desired torque.
• During pulling the switch trigger, the torque setting can-
not be changed.
• For approximately one minute after releasing the
switch trigger, the torque setting can be changed. If you
want to change the torque setting after that, pull the
switch trigger again.
• The number of torque setting does not mean specific
torque rate.
Empty signal for remaining battery capacity
(Fig. 10)
The remaining battery capacity will be signaled on the
LED display when pulling the switch trigger.
The remaining battery capacity is shown as the following
table.
Impact force grade
displayed on panel
Maximum blows
Application Work
BTP131 BTP141
Hard
3,200
(min
–1
)
3,200
(min
–1
)
Tightening when force and
speed are desired.
Tightening in underwork
material/Tightening long
screws/Tightening bolts.
Medium
2,400
(min
–1
)
2,400
(min
–1
)
Tightening when a good fin-
ishing is needed.
Tightening in the finishing
board, plaster board.
Soft
1,200
(min
–1
)
1,200
(min
–1
)
Tightening when excessive
tightening need to be avoided
because of potentially
clogged female screw and
broken or damaged screw
head.
Tightening sash screw/ Tight-
ening small screws such as
M6.
LED indicator status Remaining battery capacity
About 50% or more
About 20% – 50%
About less than 20%
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita BTP141 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita BTP141 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 5,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info