Manual Makita BTP141 (page 7 of 84) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

598664

Zoom out

Zoom in

1/84

Battery protection system (Lithium-ion battery

with star marking) (Fig. 2)

Lithium-ion batteries with a star marking are equipped

with a protection system. This system automatically cuts

off power to the tool to extend battery life.

The tool will automatically stop during operation if the

tool and/or battery are placed under one of the following

conditions:

• Overloaded:

The tool is operated in a manner that causes it to draw

an abnormally high current.

In this situation, release the trigger switch on the tool

and stop the application that caused the tool to become

overloaded. Then pull the trigger switch again to

restart.

If the tool does not start, the battery is overheated. In

this situation, let the battery cool before pulling the trig-

ger switch again.

• Low battery voltage:

The remaining battery capacity is too low and the tool

will not operate. In this situation, remove and recharge

the battery.

Switch action (Fig. 3)

CAUTION:

• Before installing the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To start the tool, simply pull the switch trigger. The tool

speed is increased by increasing pressure on the switch

trigger. Release the switch trigger to stop.

NOTE:

• The tool will stop three minutes after pulling the switch

trigger.

Lighting up the front lamp (Fig. 4 & 5)

CAUTION:

• Do not look in the lamp or see the source of lamp

directly.

Every time the lamp button on the LED display is

pressed, the lamp status is alternatively changed from

the ON to the OFF and from the OFF to the ON.

With the lamp button in the ON status, pull the switch trig-

ger to turn on the lamp. To turn off, release it and the

lamp goes out approximately 10 seconds after releasing.

With the lamp button in the OFF status, even if the trigger

is pulled, the lamp will not light on.

NOTE:

• To make sure the status of lamp, pull the trigger. When

the lamp lights up by pulling the switch trigger, the lamp

switch is in the ON status. When the lamp does not

come on, the lamp switch is in the OFF status.

• During the operation of switch trigger, the lamp status

cannot be changed.

• For approximately 10 seconds after releasing the

switch trigger, the lamp status can be switched.

Reversing switch action (Fig. 6)

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for counter-

clockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position.

Speed change (Fig. 7)

NOTICE:

• Always set the speed change lever fully to the correct

position. If you operate the tool with the speed change

lever positioned halfway between the “1” side and “2”

side, the tool may be damaged.

• Do not use the speed change lever while the tool is

running. The tool may be damaged.

• Do not force the lever to “1” side with impact driver

mode. The tool may be damaged.

To change the speed, first switch off the tool and then

slide the speed change lever to the “2” side for high

speed or “1” side for low speed. Be sure that the speed

change lever is set to the correct position before opera-

tion. Use the right speed for your job.

When turning the action mode changing ring to impact

driver mode, set the speed change lever to the “2” side.

Selecting the action mode (Fig. 8)

This tool employs an action mode changing ring. Select

one of the 4 modes suitable for your work need by turn-

ing this ring.

When driving wood screws or bolts, point the arrow at the

mark for impact driver mode. The impact force can be

adjusted on the LED display.

When drilling into concrete or tiles, point the arrow at the

mark for hammer drill mode.

When drilling into wood or metal, point the arrow at the

mark for drill mode.

When driving small wood screws or machine screws,

point the arrow at the mark for screwdriver mode. The

fastening torque can be adjusted on the LED display.

CAUTION:

• Always set the arrow correctly to either mode mark. If

you operate the tool with the action mode changing ring

positioned halfway between the mode marks, the tool

may be damaged.

• When turning the action mode changing ring, make

sure that the tool stops. If the ring does not easily

move, pull the switch trigger slightly to rotate the spin-

dle and then move the ring.

• In the hammer drill mode or drill mode, the blowing

force or torque is not adjustable. In those modes, the

number on the LED display will be off.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BTP141 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 5,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BTP141 Manual

Product: