Manual Makita BTD145 (page 7 of 60) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

598618

Zoom out

Zoom in

1/60

• After inserting the bit, make sure that it is firmly

secured. If it comes out, do not use it.

Hook (Fig. 11)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool hous-

ing on either side and then secure it with a screw. To

remove, loosen the screw and then take it out.

OPERATION

The proper fastening torque may differ depending upon

the kind or size of the screw/bolt, the material of the

workpiece to be fastened, etc. The relation between fas-

tening torque and fastening time is shown in the figures.

(Fig. 12, 13 & 14)

Hold the tool firmly and place the point of the driver bit in

the screw head. Apply forward pressure to the tool to the

extent that the bit will not slip off the screw and turn the

tool on to start operation.

NOTE:

• Use the proper bit for the head of the screw/bolt that

you wish to use.

• When fastening screw M8 or smaller, choose a proper

hammer force, and carefully adjust pressure on the

switch trigger so that the screw is not damaged.

• Hold the tool pointed straight at the screw.

• If the hammering force is too strong you tighten the

screw for a time longer than shown in the figures, the

screw or the point of the driver bit may be overstressed,

stripped, damaged, etc. Before starting your job,

always perform a test operation to determine the

proper fastening time for your screw.

The fastening torque is affected by a wide variety of fac-

tors including the following. After fastening, always check

the torque with a torque wrench.

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening

torque will be reduced.

2. Driver bit or socket bit

Failure to use the correct size driver bit or socket bit

will cause a reduction in the fastening torque.

3. Bolt

• Even though the torque coefficient and the class of

bolt are the same, the proper fastening torque will

differ according to the diameter of bolt.

• Even though the diameters of bolts are the same,

the proper fastening torque will differ according to

the torque coefficient, the class of bolt and the bolt

length.

4. The manner of holding the tool or the material of

driving position to be fastened will affect the torque.

5. Operating the tool at low speed will cause a reduc-

tion in the fastening torque.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspec-

tion or maintenance except for the following troubleshooting related to the light.

Cleaning

From time to time wipe off the outside (tool body) of the tool using a cloth dampened in soapy water.

CAUTION:

• Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.

Troubleshooting

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita replacement parts.

Trouble Light status/LED indicator status/tool status Steps to be taken

The tool

stops during

operation.

LED indicator for empty signal for remaining

battery capacity lights up.

Remaining battery capacity level is low. Charge the

battery cartridge.

When the LED indicator still lights up even after

charging the battery cartridge, the tool temperature is

high. Cool down it fully. The tool restarts after its

temperature becomes low.

When the status is still unchanged, stop using and

have the tool repaired by a Makita local service

center.

Light flickers once per second.

The tool temperature is high. Cool down it fully. The

tool restarts after its temperature becomes low.

Light flickers five times per second.

Use the tool with the motor not locked. (When the

tool has stopped due to the motor locking, withdraw

the battery cartridge one time and then insert it again

or release the switch trigger for more than

60 seconds to restart the tool.)

If the motor still remains locked, stop using and have

the tool repaired by a Makita local service center.

Switch trigger has been pulled continuously

for more than 130 seconds.

Release the switch trigger.

Other Symptoms

Stop using and have the tool repaired by a Makita

local service center.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BTD145 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BTD145 Manual

Product: