598618

Makita BTD145 Manual

6
Zoom out
Zoom in
Previous page
1/60
Next page
6
Changing the hammering force (Fig. 6)
The hammering force can be changed in three steps:
hard, medium and soft.
This allows a tightening suitable to the work.
Every time the hammering force button is pressed,
the number of blows changes in three steps.
For approximately one minute after releasing the switch
trigger, the hammering force can be changed.
NOTE:
• When all lamps on the switch panel go out, the tool is
turned off to save the battery power. The hammer force
grade can be checked by pulling the switch trigger to
the extent that the tool does not operate.
• During the operation of switch trigger, the hammer
force grade cannot be changed.
Empty signal for remaining battery capacity (Fig. 7)
Pulling the trigger switch when the remaining battery
capacity becomes very low makes LED indicator flicker.
If the tool is used continuously with the LED indicator
flickering up and the battery power is almost used up, the
LED indicator will light up and the tool itself will stop.
Please refer to the following table for the LED indicator
status and the remaining battery capacity.
NOTE:
• When all lamps on the switch panel go out, the tool is
turned off to save the battery power. The remaining
battery capacity can be checked by pulling the switch
trigger to the extent that the tool does not operate.
• All of the lamps on the switch panel go out approxi-
mately one minute after releasing the switch trigger.
• When the tool temperature is high, the LED indicator
may flicker or light up.
• If the LED indicator lights up and the tool stops even
with a recharged battery cartridge, cool down the tool
temperature fully. When the status is still unchanged,
stop using and have the tool repaired by a Makita local
service center.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before carrying out any work
on the tool.
Installing or removing driver bit or socket bit
Use only bits that has inserting portion shown in the fig-
ure. (Fig. 8)
For tool with shallow bit hole (Fig. 9)
For tool with deep bit hole (Fig. 10)
Procedure 1
For tool without one-touch type
To install the bit, pull the sleeve in the direction of the
arrow and insert the bit into the sleeve as far as it will go.
Then release the sleeve to secure the bit.
For tool one-touch type
To install the bit, insert the bit into the sleeve as far as it
will go.
Procedure 2
In addition to the procedure (1) above, insert the bit-piece
into the sleeve with its pointed end facing in.
To remove the bit, pull the sleeve in the direction of the
arrow and pull the bit out.
NOTE:
• If the bit is not inserted deep enough into the sleeve,
the sleeve will not return to its original position and the
bit will not be secured. In this case, try re-inserting the
bit according to the instructions above.
• When it is difficult to insert the bit, pull the sleeve and
insert it into the sleeve as far as it will go.
Hammering force grade
displayed on panel
Maximum blows
Application Work
BTD133 BTD145
Hard
3,200
(min
–1
)
3,400
(min
–1
)
Tightening when force and
speed are desired.
Tightening in underwork material /
Tightening long screws / Tightening
bolts.
Medium
2,600
(min
–1
)
2,800
(min
–1
)
Tightening when a good
finishing is needed.
Tightening in the finishing board,
plaster board.
Soft
1,100
(min
–1
)
1,300
(min
–1
)
Tightening when excessive
tightening need to be avoided
because of potentially clogged
female screw and broken or
damaged screw head.
Tightening sash screw / Tightening
small screws such as M6.
SH
SH
SH
LED indicator status Remaining battery capacity
OFF
Enough
Flickering
20%
Lighting on Very low and the tool will
stop.
A = 12 mm
B = 9 mm
Use only these type of bit. Follow the
procedure (1).
(Note) Bit-piece is not necessary.
A = 17 mm
B = 14 mm
To install these types of bits, follow the
procedure (1).
A = 12 mm
B = 9 mm
To install these types of bits, follow the
procedure (2).
(Note) Bit-piece is necessary for
installing the bit.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita BTD145 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita BTD145 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info