387500

Makita bhp 460 sh Manual

7
Zoom out
Zoom in
Previous page
1/88
Next page
Switch action (Fig. 7)
CAUTION:
Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the ‘‘OFF’’ position when
released.
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger.
Release the trigger to stop.
Reversing switch action (Fig. 8)
CAUTION:
•
Always check the direction of rotation before opera-
tion.
•
Use the reversing switch only after the tool comes to
a complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
•
When not operating the tool, always set the revers-
ing switch lever to the neutral position.
This tool has a reversing switch to change the direc-
tion of rotation. Depress the reversing switch lever
from the A side for forward rotation or from the B side
for reverse rotation. When the switch lever is in
between (the neutral position), the switch trigger
cannot be pulled.
Speed change (Fig. 9)
To change the speed, first switch off the tool and then
slide the speed change lever to the ‘‘II’’ side for high
speed or ‘‘I’’ side for low speed. Be sure that the
speed change lever is set to the correct position
before operation. Use the right speed for your job.
CAUTION:
•
Always set the speed change lever fully to the
correct position. If you operate the tool with the
speed change lever positioned half-way between
the ‘‘I’’ side and ‘‘II’’ side, the tool may be damaged.
•
Do not use the speed change lever while the tool is
running. The tool may be damaged.
Selecting the action mode (Fig. 10)
This tool employs an action mode changing ring.
Select one of the three modes suitable for your work
needs by using this ring. For rotation only, turn the
ring so that the arrow on the tool body points toward
the
mark on the ring. For rotation with hammer-
ing, turn the ring so that the arrow points toward the
on the ring. For screwdriving (rotation with
clutch), turn the ring so that the arrow points toward
the
mark on the ring.
CAUTION:
Always set the ring correctly to your desired mode
mark. If you operate the tool with the ring positioned
half-way between the mode marks, the tool may be
damaged.
Adjusting the fastening torque (Fig. 11)
The fastening torque can be adjusted in 16 steps by
turning the adjusting ring so that its graduations are
aligned with the arrow on the tool body. The fastening
torque is minimum when the number 1 is aligned with
the arrow, and maximum when thenumber 16 is
aligned with the arrow.
Before actual operation, drive a trial screw into your
material or a piece of duplicate material to determine
which torque level is required for a particular applica-
tion.
Screwdriving operation (Fig. 12)
First, turn the action mode changing ring so that the
arrow on the tool body points to the
marking.
Adjust the adjusting ring to the proper torque level for
your work. Then proceed as follows.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and
then increase the speed gradually. Release the trig-
ger as soon as the clutch cuts in.
NOTE:
•
Make sure that the driver bit is inserted straight in
the screw head, or the screw and/or bit may be
damaged.
•
When driving wood screws, predrill pilot holes to
make driving easier and to prevent splitting of the
workpiece. See the chart below.
Nominal diameter of
wood screw (mm)
Recommended size of
pilot hole (mm)
3.1 2.0 – 2.2
3.5 2.2 – 2.5
3.8 2.5 – 2.8
4.5 2.9 – 3.2
4.8 3.1 – 3.4
5.1 3.3 – 3.6
5.5 3.6 – 3.9
5.8 4.0 – 4.2
6.1 4.2 – 4.4
•
If the tool is operated continuously until the battery
cartridge has discharged, allow the tool to rest for
15 minutes before proceeding with a fresh battery.
BHP460 (E) (’100. 4. 19)
7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita bhp 460 sh at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita bhp 460 sh in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita bhp 460 sh

Makita bhp 460 sh User Manual - English, Dutch - 23 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info