Manual Makita bhp 460 sh (page 8 of 88) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

387500

Zoom out

Zoom in

1/88

Drilling operation

First, turn the action mode changing ring so that the

arrow on the tool body points to the

marking. The

adjusting ring can be aligned in any torque levels for

this operation. Then proceed as follows.

•

Drilling in wood

When drilling in wood, best results are obtained with

wood drills equipped with a guide screw. The guide

screw makes drilling easier by pulling the bit into the

workpiece.

•

Drilling in metal

To prevent the bit from slipping when starting a hole,

make an indentation with a centerpunch and ham-

mer at the point to be drilled. Place the point of the

bit in the indentation and start drilling.

Use a cutting lubricant when drilling metals. The

exceptions are iron and brass which should be

drilled dry.

CAUTION:

•

Pressing excessively on the tool will not speed up

the drilling. In fact, this excessive pressure will only

serve to damage the tip of your bit, decrease the

tool performance and shorten the service life of the

tool.

•

There is a tremendous force exerted on the tool/bit

at the time of hole breakthrough. Hold the tool firmly

and exert care when the bit begins to break through

the workpiece.

•

A stuck bit can be removed simply by setting the

reversing switch to reverse rotation in order to back

out. However, the tool may back out abruptly if you

do not hold it firmly.

•

Always secure small workpieces in a vise or similar

hold-down device.

•

If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

15 minutes before proceeding with a fresh battery.

Hammer drilling operation

First, turn the action mode changing ring so that the

arrow on the tool body points to the

marking.

The adjusting ring can be aligned in any torque levels

for this operation. Position the bit at the desired

location for the hole, then pull the trigger. Do not force

the tool. Light pressure gives best results. Keep the

tool in position and prevent it from slipping away from

the hole. Do not apply more pressure when the hole

becomes clogged with chips or particles. Instead, run

the tool at an idle, then remove the bit partially from

the hole. By repeating this several times, the hole will

be cleaned out and normal drilling may be resumed.

CAUTION:

There is a tremendous and sudden twisting force

exerted on the tool/bit at the time of hole break-

through, when the hole becomes clogged with chips

and particles, or when striking reinforcing rods

embedded in the concrete. Always use the side grip

(auxiliary handle) and firmly hold the tool by both side

grip and switch handle during operations. Failure to

do so may result in the loss of control of the tool and

potentially severe injury.

Blow-out bulb (Fig. 13)

Use the blow-out bulb to clean out the hole.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Replacement of carbon brushes (Fig. 14 & 15)

Replace carbon brushes when they are worn down to

the limit mark. Both identical carbon brushes should

be replaced at the same time.

To maintain product safety and reliability, repairs,

maintenance or adjustment should be carried out by a

Makita Authorized Service Center.

BHP460 (E) (’100. 4. 19)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita bhp 460 sh in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita bhp 460 sh

Makita bhp 460 sh User Manual - English, Dutch - 23 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita bhp 460 sh Manual

Product: