598477

Makita BFT120F Manual

6
Zoom out
Zoom in
Previous page
1/12
Next page
6
Lighting up front lamp (Fig. 5)
For models BFT120F/BFT121F only
CAUTION:
Do not look in the light or see the source of light directly.
Pull the switch trigger to light up the front lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The light automatically goes out 10 seconds after the
switch trigger is released.
Reversing switch action (Fig. 6)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
• When not operating the tool, always set the reversing
switch lever to the neutral position.
This tool has a reversing switch to change the direction of
rotation. Move the reversing switch lever to the
D
posi-
tion (A side) for clockwise rotation or the
E position
(B side) for counterclockwise rotation.
When the reversing switch lever is in the neutral position,
the switch trigger cannot be pulled.
LED indicator/Beeper (Fig. 7)
LED indicator/Beeper on the tool shows the following functions.
Function Status
Status of the LED indicator/beeper
Action to be taken
LED indicator Beeper
Auto-stop
fastening
This function works when the tool
has reached the preset fastening
torque and normal tightening has
been completed. This helps over-
tightening to be avoided.
Lights up in
green for
approximately
one second.
——
Delayed re-start For approximately one second
after auto-stop fastening, the tool
does not start even if the switch
trigger is pulled.
Warning against
insufficient
fastening
Insufficient fastening has been
performed when the switch trig-
ger has released before reaching
the preset fastening torque.
Lights up in red. A long beep Retighten the screw
Warning for
battery cartridge
capacity
This indicates the appropriate
time to replace the battery car-
tridge when the battery power
becomes low.
Flickers in red
slowly.
A series of long
beeps
Replace the battery
with fully charged one
Checking the
remaining battery
capacity, Autostop
This function works when the
battery power is almost used up.
At this time, tool stops immedi-
ately.
Lights up in red. A long beep Replace the battery
with fully charged one
Check the LED
indicator, light and
beeper operation
This function works to check the
proper operation of the LED indi-
cator, light and beeper when a
battery cartridge has been
inserted into the tool.
Lights up first in
green, next red.
(And then the
light comes on.)
A series of very
short beeps
—
Anti-reset of
controller
This function works when an
abnormal drop of the battery volt-
age occurs for some reason, and
the tool stops.
Flickers in red
and green
alternatively.
A series of short
beeps
Replace the battery
with fully charged one
Overheat This function works when the
temperature of the controller goes
up very highly, and the tool stops.
Flickers in red
quickly. A series of short
beeps
Remove the battery
cartridge
immediately and cool
the tool down.
Operation error of
the switch trigger
This function works to avoid the
tool’s immediate start upon inser-
tion of battery cartridge into the
tool with the switch trigger being
pulled.
Flickers in red
and green
alternatively.
A series of short
beeps
Release the switch
trigger.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita BFT120F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita BFT120F in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita BFT120F

Makita BFT120F User Manual - English, German, Polish - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info