598409
6
Zoom out
Zoom in
Previous page
1/60
Next page
6
ENGLISH
Explanation of general view
SPECIFICATIONS
Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
Note: Specifications may differ from country to country.
Symbols
END106-2
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
............. Read instruction manual.
............. Wear safety glasses.
............. Do not use on scaffoldings, ladders.
Intended use
ENE054-1
The tool is intended for pressing staples into construction
materials such as timbers.
IMPORTANT SAFETY
INSTRUCTIONS
ENB112-1
WARNING: WHEN USING THIS TOOL, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
REDUCE THE RISK OF PERSONAL INJURY,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
For personal safety and proper operation and
maintenance of the tool, read this instruction manual
before using the tool.
Always wear safety glasses to protect your eyes from
dust or staple injury.
WARNING:
It is an employer's responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
For Australia and New Zealand only
Always wear safety glasses and face shield to protect
your eyes from dust or staple injury. The safety glasses
and the face shield should conform with the
requirements of AS/NZS 1336.
WARNING:
It is an employer's responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
(Fig. 1)
Wear hearing protection to protect your ears against
exhaust noise and head protection. Also wear light but
not loose clothing. Sleeves should be buttoned or
rolled up. No necktie should be worn.
Rushing the job or forcing the tool is dangerous.
Handle the tool carefully. Do not operate when under
the influence of alcohol, drugs or the like.
General Tool Handling Guidelines:
(1) Always assume that the tool contains fasteners.
(2) Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
(3) Do not activate the tool unless the tool is placed
firmly against the workpiece.
(4) Respect the tool as a working implement.
(5) No horseplay.
(6) Do not hold or carry the tool with a finger on the
trigger.
(7) Do not load the tool with fasteners when any one
of the operating controls is activated.
1. Safety glasses
2. Face shield
3. Contact element
4. Trigger
5. Workpiece
6. Compressor air output per minute
7. Nailing frequency
8. Adjuster
9. Deep
10. Shallow
11. Too deep
12. Flush
13. Too shallow
14. Screw
15. Hook
16. Groove
17. Protrusion
18. Flat nose adapter
19. Staple stopper
20. Pusher base
21. Pusher
22. Change lever
23. Exhaust cover
24. Exhaust vent
25. Hex wrench
26. Front guide
27. Contact top
28. Drain cock
29. Air filter
30. Oiler
31. Pneumatic oil
32. Thinner
33. Stove
Model AT450H
Air pressure 1.28 - 2.26 MPa (12.8 - 22.6 bar)
Applicable staples 25 mm - 50 mm
Staple capacity 84 pcs. (1 strip), max. 105 pcs.
Min. hose diameter 5.0 mm
Dimensions (L X H X W) 261 mm X 115 mm X 269 mm
Net weight 1.4 kg
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita AT450H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita AT450H in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info