691015

Makita 9921 Manual

5
Zoom out
Zoom in
Previous page
1/40
Next page
ENGLISH
Explanation of general view
1 Lever
2 Adjusting knob
3 Dust bag
4 Dust nozzle
5 Fastener
6 Lock button
7 Switch trigger
8 Cork rubber plate
9 Carbon plate or steel plate
0 Strap washer
q Limit mark
w Brush holder cap
e Screwdriver
SPECIFICATIONS
Model 9403 9921
Belt size .................................................................................. 100 mm x 610 mm 76 mm x 610 mm
Belt speed .............................................................................. 500 m/min. 500 m/min.
Overall length ......................................................................... 353 mm 353 mm
Net weight .............................................................................. 5.9 kg 5.5 kg
•
Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
•
Note: Specifications may differ from country to
country.
Power supply
The tools should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause volt-
age fluctuations. The operation of this device under
unfavorable mains conditions can have adverse
effects to the operation of other equipment. With a
mains impedance equal or less than 0.43 Ohms it can
be presumed that there will be no negative effects.
The mains socket used for this device must be
protected with a fuse or protective circuit breaker
having slow tripping characteristics.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
ADDITIONAL SAFETY RULES
1. Hold toolss by insulated gripping surfaces
when performing an operation where the cut-
ting tools may contact hidden wiring or its
own cord. Contact with a ‘‘live’’ wire will make
exposed metal parts of the tools ‘‘live’’ and
shock the operator.
2. Hold the tools firmly with both hands.
3. Make sure the belt is not contacting the work-
piece before the switch is turned on.
4. Keep hands away from rotating parts.
5. Do not leave the tools running. Operate the
tools only when hand-held.
6. This tools has not been waterproofed, so do
not use water on the workpiece surface.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing abrasive belt
(Fig.1&2)
Important:
Always be sure that the tools is switched off and
unplugged before installing or removing the belt.
Pull the lever all the way out and install the belt over
the rollers, then return the lever to the original posi-
tion.
CAUTION:
When installing the belt, make sure that the direction
of the arrow on the back of the belt corresponds to the
one on the tools itself.
Adjusting belt tracking (Fig. 3)
While the belt is running, use the adjusting knob to
center the belt tracking.
Dust bag (Fig.4&5)
Attach the dust bag onto the dust nozzle. The dust
nozzle is tapered. When attaching the dust bag, push
it onto the dust nozzle firmly as far as it will go to
prevent it from coming off during operation. For the
best results, empty the dust bag when it becomes
about half full, tapping it lightly to remove as much
dust as possible.
9403/9921 (E) (’100. 10. 11)
5
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 9921 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 9921 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info