78953

Makita 6802 Manual

3
Zoom out
Zoom in
Previous page
1/12
Next page
3
ENGLISH
Explanation of general view
1 Locking position
2 Locator
3 Locking sleeve
4 Magnetic socket bit
5 Gear housing
6 Socket bit
7Low
8 High
9 Speed control screw
10 Switch trigger
11 Lock button
12 Reversing switch lever
13 Insert bit
14 Magnetic bit holder
SPECIFICATIONS
Model 6802BV
Capacities
Self drilling screw ...........................................6 mm
Bit shank size ............................................... 1/4” Hex
No load speed (min
-1
) ................................0 – 2,500
Overall length ................................................265 mm
Net weight ........................................................1.7 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
SPECIFIC SAFETY RULES
GEB017-1
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict
adherence to screwdriver safety rules. If you use
this tool unsafely or incorrectly, you can suffer
serious personal injury.
1. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will make exposed metal
parts of the tool “live” and shock the operator.
2. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
OPERATING INSTRUCTIONS
Removing or installing locator assembly
(Fig. 1)
To remove the locator assembly, pull the locking
sleeve forward and then turn it counterclockwise. To
install the locator assembly, screw it clockwise and
then push the locking sleeve back in lightly toward
the motor. Turn the locking sleeve slightly to match
the locking positions and then push in firmly to lock
the locator in place.
Removing or installing magnetic socket bit
(Fig. 2)
Important:
Always be sure that the tool is switched off and
unplugged before removing or installing the bit.
After removing the locator assembly, pull firmly to
remove the magnetic socket bit. To install the bit,
insert it into the tool as far as it will go.
Depth adjustment (Fig. 3 & 4)
Pull the locking sleeve forward and then turn it to
adjust the depth.
Initially, adjust the locator assembly to create a dis-
tance of approximately 0.5 mm from the tip of the
locator to the tip of the socket bit. One full turn of the
locator equals 1.5 mm change in depth. After adjust-
ing the locator assembly, push the locking sleeve in to
lock the locator in place. Drive a trial screw into your
material or a piece of duplicate material. If the depth
is not suitable for the screw, continue adjusting until
the proper depth setting is obtained.
Switch action (Fig. 5)
CAUTION:
Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
“OFF” position when released.
To start the tool, simply pull the trigger. tool speed is
increased by increasing pressure on the trigger.
Release the trigger to stop. For continuous operation,
pull the trigger and then push in the lock button. To
stop the tool from the locked position, pull the trigger
fully, then release it. A speed control screw is pro-
vided so that maximum tool speed can be limited
(variable). Turn the speed control screw clockwise for
higher speed, and counterclockwise for lower speed.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 6802 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 6802 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info