Manual Makita 6702DW (page 6 of 56) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

690969

Zoom out

Zoom in

1/56

Reversing switch action (Fig. 7)

CAUTION:

•

Always check the direction of rotation before opera-

tion.

•

Use the reversing switch only after the machine

comes to a complete stop. Changing the direction of

rotation before the machine stops may damage the

machine.

This machine has a reversing switch to change the

direction of rotation. Slide the reversing switch up for

clockwise rotation or slide it down for counterclock-

wise rotation.

Overload protector

The overload protector automatically cuts out to break

the circuit whenever heavy work is prolonged. Wait

20 – 30 seconds before resuming operation.

Adjusting the fastening torque (Fig. 8)

The fastening torque can be adjusted infinitely from

approx. 20 kg·cm to 80 kg·cm. To adjust it, loosen the

two screws and turn the adjusting ring. Then tighten

the screws to secure the adjusting ring. Refer to the

table below for relation between the numbers on the

adjusting ring and the fastening torque to be obtained.

Numbers on

adjusting ring

Fastening torque to

be obtained

1 20 kg·cm

2 35 kg·cm

3 48 kg·cm

4 60 kg·cm

5 80 kg·cm

(Example)

35 kg·cm of fastening torque can be obtained when

the number 2 is aligned to the red mark.

NOTE:

•

Always tighten the two screws to secure the adjust-

ing ring after adjusting the fastening torque.

•

The fastening torque may differ depending upon the

kind of screws, the type of materials to be fastened,

etc. Before starting your job, always perform a test

operation to verify the adequate fastening torque.

Operation

The proper fastening torque may differ depending

upon the kind or size of screws, the type of materials

to be fastened, the condition of the threads, etc.

Before starting your job, always perform a test opera-

tion to verify adequate fastening torque.

Hold the machine firmly with both hands whenever

possible and place the socket over the bolt or nut.

Then turn the machine on. As soon as the bolt or nut

becomes tight, the clutch will cut in and the motor will

stop automatically. Release the switch trigger.

When fastening machine screws, use the proper

screwdriver bit shown in Fig. 9. It is commonly avail-

able on the market.

NOTE:

•

Always use the correct size socket for bolts and

nuts. An incorrect size socket will result in inaccu-

rate and inconsistent fastening torque and/or dam-

age to the bolt or nut.

•

Hold the machine with its square drive pointed

straight at the bolt or nut, or the bolt or nut will be

damaged.

•

If the motor will not start even after you pull the

trigger, release the trigger. Then pull the trigger

again after turning the socket slightly with your

fingers.

Fastening performance

The following reference table indicates the approximate fastening capacity from a single 1-hour battery charge.

It may differ under some conditions.

Screw size Fastening torque Fastenings

M6x14

5 About 800 screws

1 About 1,000 screws

MAINTENANCE

CAUTION:

Always be sure that the machine is switched off and

the battery cartridge is removed before carrying out

any work on the machine.

To maintain product safety and reliability, repairs,

maintenance or adjustment should be carried out by

Makita Authorized Service Center.

6702D (E) (’97. 9. 19)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 6702DW in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 6702DW Manual

Product: