Manual Makita 6702DW (page 5 of 56) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

690969

Zoom out

Zoom in

1/56

ADDITIONAL SAFETY RULES

FOR MACHINE

1. Be aware that this machine is always in an

operating condition, because it does not have

to be plugged into an electrical outlet.

2. Always be sure you have a firm footing. Be

sure no one is below when using the machine

in high locations.

3. Hold the machine firmly.

4. When driving into walls, floors or wherever

‘‘live’’electrical wires may be encountered, DO

NOT TOUCH ANY METAL PARTS OF THE

MACHINE! Hold the machine only by the insu-

lated grasping surfaces to prevent electric

shock if you drive into a ‘‘live’’ wire.

5. Check the socket carefully for wear, cracks or

damage before installation.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge

(Fig. 1)

•

Always switch off the machine before insertion or

removal of the battery cartridge.

•

To remove the battery cartridge, pull out the set

plate on the machine and grasp both sides of the

cartridge while withdrawing it from the machine.

•

To insert the battery cartridge, align the tongue on

the battery cartridge with the groove in the housing

and slip it into place. Snap the set plate back into

place. Be sure to close the set plate fully before

using the machine.

•

Do not use force when inserting the battery car-

tridge. If the cartridge does not slide in easily, it is

not being inserted correctly.

Charging (Fig. 2)

Plug the fast charger into your power source. Insert

the battery cartridge so that the plus and minus

terminals on the battery cartridge are on the same

sides as their respective markings on the fast charger.

The charging light will come on and charging will

begin. If the charging light goes out soon, remove the

battery cartridge from the charger and let it cool off for

more than one minute. Then re-insert it and try to

charge it once more. If the charging light goes out

within one minute even after repeating this procedure

a couple of times, the battery cartridge is dead.

Replace it with a new one. When the charging light

goes out after about one hour, you may remove the

fully charged battery cartridge.

After charging, unplug the charger from the power

source.

Battery type

Capacity

(mAH)

Number of

cells

9100 1,300 8

CAUTION:

•

Your new battery cartridge is not charged. You will

need to charge it before use.

•

If you try to charge a cartridge from a just-operated

machine, sometimes the charging light will not

come on. If this occurs, let the cartridge cool off for

a while. Then re-insert it and try to charge it once

more.

•

When you charge a new battery cartridge or a

battery cartridge which has not been used for a long

period, it may not accept a full charge. This is a

normal condition and does not indicate a problem.

You can recharge the battery cartridge fully after

discharging it completely a couple of times.

•

If you wish to charge two battery cartridges, allow

15 minutes between chargings on the fast charger.

Installing or removing socket

Important:

Always be sure that the machine is switched off and

the battery cartridge is removed before installing or

removing the socket.

For machine with square drive (Fig.3&4)

Use 9.5 mm square drive socket with a hole for detent

pin which is available on the market. (Note: Use

6.35 mm square drive socket when using the machine

with 6.35 mm square drive.)

To install the socket, depress the detent pin on the

square drive with your finger and push the socket onto

the square drive until the detent pin is inserted into the

hole in the socket.

To remove the socket, depress the detent pin with a

small hand tool and pull off the socket.

For machine with round drive (Fig. 5)

Use a bit with Form C 6.3 shank which is available on

the market. The bit can be inserted directly into the

round drive and held in place.

To install the bit, push it firmly into the round drive.

To remove the bit, grasp it with a pair of pliers and pull

it out of the round drive. Sometimes, it helps to wiggle

the bit with the pliers as you pull.

Switch action (Fig. 6)

CAUTION:

Before inserting the battery cartridge into the

machine, always check to see that the switch trigger

actuates properly and returns to the ‘‘OFF’’ position

when released.

To start the machine, simply pull the trigger. Release

the trigger to stop.

6702D (E) (’97. 9. 19)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 6702DW in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 6702DW Manual

Product: