383013

Makita 4333 d Manual

6
Zoom out
Zoom in
Previous page
1/12
Next page
6
ADDITIONAL SAFETY RULES FOR TOOL
ENB030-1
1. Be aware that this tool is always in an operating
condition, because it does not have to be
plugged into an electrical outlet.
2. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring. Contact with a “live”
wire will make exposed metal parts of the tool
“live” and shock the operator.
3. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
4. Do not cut hollow pipe.
5. Do not cut oversize workpiece.
6. Check for the proper clearance beneath the
workpiece before cutting so that the blade will
not strike the floor, workbench, etc.
7. Hold the tool firmly.
8. Check the blade is not contacting the workpiece
before the switch is turned on.
9. Keep hands away from moving parts.
10. Do not leave the tool running. Operate the tool
only when hand-held.
11. Always switch off and wait for the blade to come
to a complete stop before removing the blade
from the workpiece.
12. Do not touch the blade or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge (Fig.1)
• Always switch off the tool before insertion or removal of the battery cartridge.
• To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge.
• To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into
place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool,
causing injury to you or someone around you.
• Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted
correctly.
Installing or removing saw blade (Fig. 2 &3)
CAUTION:
• Always be sure that the tool is switched off and unplugged before installing or removing the blade.
• Always clean out all chips or foreign matter adhering to the blade and/or blade holder. Failure to do so may cause
insufficient tightening of the blade, resulting in a serious injury.
• Use a lubricant or cutting oil between the blade and roller when cutting iron or composition board, etc. Failure to do
so will shorten the service life of your blade and roller or lead to potentially dangerous blade breakage.
To install the blade, loosen the bolt on the blade holder with the hex wrench. With the blade teeth facing forward, insert
the blade into the blade holder as far as it will go. Make sure that the back edge of the blade fits into the roller. Then
tighten the bolt to secure the blade.
To remove the blade, follow the installation procedures in reverse.
NOTE:
Occasionally lubricate the roller.
Installing universal shank jig saw blade (Fig.4 & 5)
CAUTION:
Always be sure that the tool is switched off and unplugged before installing or removing the blade.
If the universal blade clamp is used, you can use blades of other makes which have a universal shank like the one
shown in the figure, with a blade width of 6.35mm. Insert the blade into the blade holder as far as it will go. Make sure
that the end of the blade shank reaches the bottom of the inner slit and tighten the bolt securely with the hex wrench.
Selecting the cutting action (Fig. 6)
This tool can be operated with an orbital or a straight line (up and down) cutting action. The orbital cutting action
thrusts the blade forward on the cutting stroke and greatly increases cutting speed.
To change the cutting action, just turn the lever to the desired cutting action position. Refer to the table below to select
the cutting action.
Position Cutting action Applications
O
Straight line cutting action For cutting mild steel, stainless steel and plastics.
For clean cuts in wood and plywood.
I Small orbit cutting action For cutting mild steel, aluminum and hard wood.
II
Medium orbit cutting action For cutting wood and plywood.
For fast cutting in aluminum and mild steel.
III Large orbit cutting action For fast cutting in wood and plywood.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 4333 d at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 4333 d in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info