383013
5
Zoom out
Zoom in
Previous page
1/12
Next page
5
ENGLISH
Explanation of general view
1 Button
2 Battery cartridge
3 Loosen
4 Hex wrench
5Bolt
6 Jig saw blade
7 Roller
8 The end of the blade shank
should reach the bottom of the
inner slit.
9Lever
10 Speed adjusting dial
11 Lock-off button
12 Switch trigger
13 Base
14 Cutting line
15 Bolt
16 Cross-shaped slot
17 Edge of motor housing
18 Graduations
19 Starting hole
20 Anti-splintering device
21 Plastic base plate
22 Guide rule
23 Threaded knob
24 Circular guide
25 Pin
26 Fit into notches.
27 Plastic cover
28 Nozzle
29 Limit mark
30 Screwdriver
31 Brush holder cap
SPECIFICATIONS
Model 4331D 4333D
Length of stroke ........................................................................... 26 mm 26 mm
Max. cutting capacities
Wood ........................................................................................ 65 mm 65 mm
Mild steel .................................................................................. 10 mm 10 mm
Aluminum .................................................................................. 20 mm 20mm
Strokes per minute ...................................................................... 500 2,800 500 2,600
Overall length .............................................................................. 280 mm 280 mm
Net weight .................................................................................... 2.6 kg 2.9 kg
Rated voltage .............................................................................. D.C.12 V D.C.14.4V
Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
Note: Specifications may differ from country to country.
Intended use
The tool is intended for the sawing of wood, plastic and
metal materials.
As a result of the extensive accessory and saw blade
program, the tool can be used for many purposes and is
very well suited for curved or circular cuts.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
ENC004-1
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
7. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
8. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
9. Be careful not to drop or strike battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera-
ture at 10°C 40°C (50°F 104°F). Let a hot bat-
tery cartridge cool down before charging it.
4. Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 4333 d at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 4333 d in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info