Manual Makita 2712 (page 9 of 72) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

690940

Zoom out

Zoom in

1/72

Switched on the dust extraction system before

starting the tool.

35. The guard can be lifted during workpiece setup

and for ease of cleaning. Always make sure that

guard hood is down and flat against sawtable

before plugging in the tool.

36. Wear gloves against the hazard of cutting when

handling saw blades, feeding wood into the tool or

doing maintenance.

37. Never try to remove chips while the saw blade is

running or the tool is switched on.

38. Never try to use the tool unless all guards and

other safety devices necessary for tool are in

good working order.

39. Operators must be adequately trained in the

assembly, adjustment and operation of the tool.

40. Never use the blades which maximum speed is

lower than the no load speed of the tool.

41. Keep work area well lit.

SAVE THESE INSTRUCTIONS.

INSTALLATION

PREPARATION

Check contents of package for the following components.

Please inform Makita service center of any part missing in

the package immediately.

- Table saw (1 unit)

- Leg (4 pcs)

- Foot (4 pcs)

- Countersunk screw for foot (4 pcs)

- Hex nut for foot (4 pcs)

- Leg support (long) (2 pcs)

- Leg support (short) (2 pcs)

- Tire complete (1 pc)

- Dust nozzle (1 pc)

- Carrying handle (2 pcs)

- Square neck bolt for guide rail (4 pcs)

- Hex bolt for guide rail (4 pcs)

- Guide rail (long) (1 pc)

- Guide rail (short) (1 pc)

- Sub table (1 pc)

- Stay (long) (2 pc)

- Stay (short) (2 pc)

- Hook (1 pc)

- Blade guard (1 pct)

- Tapping screw (3 pcs)

- Hex bolt (38 pcs)

- Hex nut (38 pcs)

- Hex wrench (1 pc)

- Wrench (1 pc)

- Push stick (1 pc)

- Push block (1 pc)

- Fence (for Rip fence) (1 pc)

- Rip fence (1 pc)

Installing table saw

1. Overturn the table saw on two boards. Check the

riving knife positions the space between two boards.

(Fig. 1)

2. Attach the four legs to the inside of base edge. Attach

the leg with the hole for the switch to the side with the

sign “A” on the base. Secure the four legs temporarily,

do not tighten the screws firmly yet. (Fig. 2)

3. Attach the leg supports (long) to the legs and then

attach the leg supports (short) to the legs. Secure the

legs and leg supports with the screws firmly. Always

check the direction of support legs.

4. Install the feet at the bottoms of the legs. Secure them

with countersunk screws and hex nuts. (Fig. 3)

5. Install the tire complete to the legs and secure them

with screws and hex nuts. (Fig. 4)

6. Install the dust nozzle.

7. Adjust the motor part to the 0° position and secure it

by tightening the knob. Secure the power cord with the

cord clamp. (Fig. 5)

8. Turn the table saw back and then attach the carrying

handles. (Fig. 6)

9. Install the switch to the leg and secure it with the

tapping screws. (Fig. 7)

10. Install the saw blade and blade guard. When installing

them, refer to the Section “Removing or installing saw

blade” and “Installing blade guard”.

11. Install the guide rail (short) to the front side of the table

saw and the guide rail (long) to the left side of the

base. (Fig. 8)

12. Install the sub table to the base. Select the proper

length stays depending on the position. (Fig. 9 & 10)

13. Install the hook to the leg. (Fig. 11)

14. Locate the table saw in a well lit and level area where

you can maintain good footing and balance. It should

be installed in an area that leaves enough room to

easily handle the size of your workpieces.

If there is any tendency for the table saw to tip over,

slide or move during operation, the table saw should

be secured to the floor.

Storing accessories (Fig. 12)

Push stick and wrenches can be stored on the right side

of the tool.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Adjusting the depth of cut (Fig. 13)

The depth of cut may be adjusted by turning the handle.

Turn the handle counterclockwise to raise the blade or

clockwise to lower it.

NOTE:

• Use a shallow depth setting when cutting thin materials

in order to obtain a cleaner cut.

Adjusting the bevel angle (Fig. 14)

Loosen the lock knob counterclockwise and the desired

angle (0° - 45°) is obtained. The arrow pointer indicates

the bevel angle.

After obtaining the desired angle, tighten the lock knob

clockwise to secure the adjustment.

CAUTION:

• After adjusting the bevel angle, be sure to tighten the

lock knob securely.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 2712 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 3,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 2712 Manual

Product: