Manual Makita 2414 (page 8 of 16) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

110245

Zoom out

Zoom in

1/16

Switch action

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

For tools with lock-off button (Fig. 12)

To prevent the trigger from being accidentally pulled, a

lock-off button is provided. To start the tool, press in the

lock-off button and pull the trigger. Release the trigger to

stop.

For tools with lock button (Fig.13)

To start the tool, simply pull the trigger. Release the trig-

ger to stop. For continuous operation, pull the trigger and

then push in the lock button. To stop the tool from the

locked position, pull the trigger fully, then release it.

Operation

Hold the handle firmly. Switch on the tool and wait until

the wheel attains full speed before lowering gently into

the cut. When the wheel contacts the workpiece, gradu-

ally bear down on the handle to perform the cut. When

the cut is completed, switch off the tool and WAIT UNTIL

THE WHEEL HAS COME TO A COMPLETE STOP

before returning the handle to the fully elevated position.

CAUTION:

Proper handle pressure during cutting and maximum cut-

ting efficiency can be determined by the amount of

sparks that is produced while cutting. Your pressure on

the handle should be adjusted to produce the maximum

amount of sparks. Do not force the cut by applying exces-

sive pressure on the handle. Reduced cutting efficiency,

premature wheel wear, as well as, possible damage to

the tool, cut-off wheel or workpiece may result.

Cutting capacity

Max. cutting capacity varies depending upon the cutting angle and workpiece shape. Applicable wheel

diameter: 355 mm

Tool head slide system

The tool head slides back toward you approx. 17 mm when you pull the handle. This system is convenient for the fol-

lowing applications.

1. When cutting thick pipes or bars: (Fig. 14)

Move the handle back and forth to slide the tool head. This will help increase cutting efficiency and prevent wheel

2. When cutting channels or angles: (Fig. 15)

If a portion of the workpiece near you is left uncut, pull the handle. The tool head slides back and the wheel cuts

the remaining uncut portion. If the uncut portion cannot be cut even by using this method, use a spacer block as

explained above.

For tools with the under cover (Fig. 16)

To remove the collected dust from the under cover, place

the tool with its side up and pull the under cover open

after removing the wing bolt as shown in the figure. Be

sure to close and secure the under cover with the wing

bolt after the removal of dust.

Carrying the tool (Fig. 17)

Fold down the tool head to the position where you can

attach the chain to the hook on the handle.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Replacement of carbon brushes (Fig. 18 & 19)

Replace carbon brushes when they are worn down to the

limit mark. Both identical carbon brushes should be

replaced at the same time.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Center.

Workpiece

shape

Cutting

angle

90° 115 mm 120 mm

115mmx142mm

102mmx197mm

70 mm x 240 mm

139 mm

45° 115 mm 106 mm 115 mm x 102 mm 100 mm

A x B B

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 2414 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 2414 Manual

Product: